Telguard Dual Path Series Installation & Operating Manual Download Page 18 | Manualshive

Page: 18 / 42

background image

TG-7 Dual Path Series Installation & Operating Guide

12

56052601 Rev B © 2022 Telguard

UL and ULC Compliance

The TG-7 Dual Path Series communicators are certified as complying with UL and ULC Standards for
Commercial Fire and Commercial Burglary installations. The chart on Page 1 shows the associated
UL and ULC Standards. Certificates of Compliance are available at

portal.telguard.com

UL/ULC Compliance Note:

The alarm panel must also be UL, ULC, or cUL Listed for commercial

fire and/or commercial burglary use as appropriate

.

ULC Compliance Note:

For Commercial Fire installations in Canada, the radio frequency warning

label (supplied with the TG-7FE) must be affixed to the outside front cover of the TG-7FE.

«
...
16
17
18
19
20
...
»

Summary of Contents for Dual Path Series











































Reviews:

No comments

Related manuals for Dual Path Series

Brand: Radio Shack Pages: 64

Brand: O2 Pages: 72

Brand: T-Mobile Pages: 4

Brand: T-Mobile Pages: 158

Brand: T-Mobile Pages: 212

Brand: Audiovox Pages: 13

Brand: Alcatel Pages: 4

Sensation 4G T-Mobile

Brand: HTC Pages: 38

ONE TOUCH 6033A

Brand: Alcatel Pages: 21

Flash Mini 4031D

Brand: OneTouch Pages: 21

Brand: ATL Pages: 4

Brand: SoftBank Pages: 9

3rd Generation Wi-Fi Phone

Brand: EZLoop Pages: 82

Brand: Samsung Pages: 102

Brand: Samsung Pages: 128

Brand: Samsung Pages: 1

Brand: Pantech Pages: 60

Brand: Garmin Pages: 73

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands