Telex SAFE-1000 User Manual Download | Manualshive

Page: 5 / 10

background image

Telex SAFE-1000 System

SAFE-WT Transmitter.

RF Power Output 5 mW Low, 50 mW High (typical), Terminated.
Antenna……………………………………..1/4 Wave flexible.
Modulation Type……NFSK, 200F1E……FM, 40 KHz Deviation.
Modulation Limiter…………………………Limiter/Compressor.
Audio Input…………………………………7.75 mV for 40 KHz Deviation.
(77.5 mV for instruments).
Power………………………………………..9.0 VDC (Alkaline).

SAFE-HT Transmitter.

RF Power Output 5 mW Low, 50 mW High (typical), Terminated.
Antenna……………………………………..Internal ½ Wave Dipole.
Modulation Type……NFSK, 200f1E……FM, 40 KHz Deviation.
Modulation Limiter…………………………Limiter/Compressor.
Audio Input…………………………………7.75 mV for 40 KHz Deviation.
Power………………………………………..9.0 VDC (Alkaline).

«
...
3
4
5
6
7
...
»

Summary of Contents for SAFE-1000











Reviews:

No comments

Related manuals for SAFE-1000

Brand: KAM Pages: 4

Brand: Roland Pages: 2

SATELLITE SCM 1820S

Brand: Gecko Pages: 12

Brand: Sennheiser Pages: 17

SureCross DX99 FlexPower DX99N9X2S0N0R4X0A0

Brand: Banner Pages: 7

Brand: Component Solution Services Pages: 14

Brand: Midland Pages: 14

Brand: Fame Audio Pages: 9

Brand: Comica Pages: 52

Brand: Zack Audio Pages: 32

Brand: Vectra Fitness Pages: 4

Brand: Konix Pages: 20

Brand: Miktek Pages: 2

Brand: Sennheiser Pages: 110

Brand: Saramonic Pages: 2

Brand: Saramonic Pages: 8

Brand: Saramonic Pages: 16

Freeway ATW-251

Brand: Audio Technica Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands