Teletek electronics CA824, Installation Manual, Page: 24 / 32

24 CA824 Installation manual
DIO32 module (Dynamic indication)
A layout of the DIO dynamic indication module is given in Fig. 16.
Use of DIO32 module
The DIO32 module is designed to make dynamic indication mnemo-panels. Visualisation of the system
area status (ALARM / MEMORY, NORMAL, ARM and DISARM) or of the system zone status (TAMPER/
FIRE, ALARM / MEMORY, OPEN or CLOSE) is possible. The zones have been divided into two areas –
from 1 to 32 and from 33 to 64.
DIO32 module resources
The DIO module has one programmable output marked PGM. This is a potential output. The program-
mable PGM output has been duplicated by a “dry” contact relay. The relay contacts are labelled COM,
NO and NC.
The BLACK, GREEN, YELLOW and RED terminals are used to connect the module to the system bus.
Auxiliary devices (sensors, sound indicators, etc.) are powered by the +AUX and +PGM control panel or
by the +12V power supply tapped at the +PGM clamp.
!Attention must be paid that the RED (+12V) clamp system bus supply is tapped to the + PGM
clamp. This supply can be controlled by the processing block at the control panel and can be
interrupted!
Two ….. type couplings have been placed on the board. These couplings are designed to connect the
light-emitting diodes at the mnemo-panel. The Anode/Cathode correspondence has to be observed
when connecting these light-emitting diodes – Fig. 16 – Anode row and Cathode row.
!Connect light-emitting diodes only to the light-emitting diode indication outputs!
Fig. 16 DIO32 dynamic indication module
BUZZER
LED
JP1
JP2
JP3
BUZZER
AREAS / ZONES
1 - 32 / 33 - 64
DIO - 32
ver. 2.0
LED LIGHT CONTROL
-
+
1 2 3 4 5 6 7 8 9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
3
3
3
4
3
5
3
6
3
7
3
8
3
9
4
0
4
1
4
2
4
3
4
4
4
5
4
6
4
7
4
8
4
9
5
0
5
1
5
2
5
3
5
4
5
5
5
6
5
7
5
8
5
9
6
0
6
1
6
2
6
3
6
4
R
E
D
Y
E
L
L
O
W
G
R
E
E
N
B
L
A
C
K
+
P
G
M
P
G
M
N
O
N
C
C
O
M
TEST
ANODE
CATHODE
ANODE
CATHODE
LED brightness
adjustment
Sound signal for
integrated
programmable
output
(JP1 - CLOSED)
Office
indication
Support openings
Support openings
1 2 3
4 5 6
7 8 9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7
1
8
1
9
2
0
2
1
2
2
2
3
2
4
2
5
2
6
2
7
2
8
2
9
3
0
3
1
3
2
1 2 3 4 5 6 7 8 9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
AREAS (ARMED or DISARMED)
(JP2 - OPEN)
AREAS (ALARM/MEMORY or NORMAL STATE)
(JP2 - OPEN)
ZONES (JP2 - CLOSED; JP3 - OPEN for 1 - 32 ZONE or JP3 - CLOSED for 33 - 64 ZONE)