manualshive.com logo in svg

Telegesis ETRX2USB, Command Manual, Page: 85 / 101

Share
Download
Telegesis ETRX2USB Command Manual Download Page 85

 

 

R305 AT Commands

 

 

©2011 Telegesis (UK) Ltd 

- 85 - 

 AT Command Manual (Rev 3.05) 

4.6  Advanced Settings 

 

S3E 

– Multicast Table Entry 00 

Description 

The ID portion of Multicast Table Entry 00 
 

Operations 

R/W LOCAL 
R/W REMOTE   

 

Becomes effective 

Instantly

 

 

Note 

Same effect as AT+MSET, but can be set at 
boot-up by built-in functionality 
 

Storage 

Non-Volatile

 

Parameters 

XXXX 

 
If S3E 

is not set to all 0‟s multicast table entry 1 to 

endpoint 1 (the AT command layer‟s endpoint) is 
set with the setting of this register is created 
instantly and after a reset. 

 

 
 

 

 
 
 

Factory Default 

0000

 

SW release  

R300   

 

 

 

 

        

● 

 

S3F 

– Multicast Table Entry 01 

Description 

The ID portion of Multicast Table Entry 01 
 

Operations 

R/W LOCAL 
R/W REMOTE   

 

Becomes effective 

Instantly

 

 

Note 

As for S3E 
 

Storage 

Non-Volatile

 

Parameters 

XXXX 

 

If 

S3F is not set to all 0‟s multicast table entry 2 to 

endpoint 1 (the AT command layer‟s endpoint) is 
set with the setting of this register is created 
instantly and after a reset. 

 

 

 

 
 
 

Factory Default 

0000

 

SW release  

R300   

 

 

 

 

        

● 

 

Summary of Contents for ETRX2USB






































































































Reviews:

No comments