Telegesis ETRX2USB Command Manual Download Page 80 | Manualshive

Page: 80 / 101

Telegesis ETRX2USB Command Manual Download Page 80

R305 AT Commands

©2011 Telegesis (UK) Ltd

- 80 -

AT Command Manual (Rev 3.05)

S33

–Timer/Counter 5

Description

A multipurpose Timer/Counter whose
functionality is defined by S34

Operations

R/W LOCAL
R/W REMOTE

Becomes effective

Instantly

Storage

Non-Volatile

Parameters

XXXX

A  16-bit  hexadecimal  number  representing  a
threshold  for  either  a  timer  or  counter  event  to  be
triggered.  When reading this register the threshold
rather  than  the  actual  timer/counter  value  is
displayed.
If  set  to  0  the  corresponding  functionality  is
disabled.

Factory Default

0000

SW release

R300

S34

– Functionality For Timer/Counter 5

Description

Defines the functionality for Timer/Counter 5
events.

Operations

R/W LOCAL
R/W REMOTE

Becomes effective

Instantly

Storage

Non-Volatile

Parameters

XXXX

If set to 0 the functionality is disabled. Please see
section 5 for a list of the functionalities.

Factory Default

0000

SW release

R300

«
...
78
79
80
81
82
...
»

Summary of Contents for ETRX2USB






































































































Reviews:

No comments