background image

5

Configuration

28 / 52

DoorLine TM4

5.14

Defining call duration to extension line

Definition of the duration of the door call to the extension line of your PBX sys-
tem.

Delivery status: 30 seconds
Possible values: 1 to 99 seconds.

The duration of the door call to the extension line can only be adjusted
if the call reception is set to "button redial". If call reception is set to "dir-
ect mode", the setting of the call duration has no effect. When a bell
pushbutton is actuated, the set time for the call duration starts running
immediately.

1.

Enter the configuration mode (see Entry to configuration
mode [

}

 19])

2.

Actuate the hashtag button and star button on the tele-
phone

3.

Enter configuration command "08" at the telephone

As confirmation, you will hear a neutral acknowledgement
tone

4.

Enter call duration with digits 01, ... 99 (in steps of one
second). 
The input must have two digits

Finally, you will hear the acknowledgement tone

5.15

Defining type of call reception

Determines the way a call is received at the telephone after a bell pushbutton
is pressed at the DoorLine.

Summary of Contents for DoorLine TM4





















































Reviews: