Telegärtner DoorLine TM4 Operating And Assembly Instructions Manual Download Page 44

Page: 44 / 52

Everyday use

44 / 52

DoorLine TM4

7.5

Direct commands during voice
communication

During a door call, you have the following additional input options on your tele-
phone:

Disconnects the connection immediately. DoorLine moves
to standby

Deactivate call forwarding pushbutton 1

Activate call forwarding pushbutton 1

Deactivate call forwarding pushbutton 2

Activate call forwarding pushbutton 2

Deactivate call forwarding pushbutton 3

Activate call forwarding pushbutton 3

Deactivate call forwarding pushbutton 4

Activate call forwarding pushbutton 4

Activates the door opener

Function is only available if

▪ a relay contact is configured as door opener and

– the door call was set up by the DoorLine

– the door opener function was enabled in the config-

uration of the DoorLine

automatic door opening deactivated (factory setting).

automatic door opening with actuation of bell pushbutton
1, without call signalling

automatic door opening with actuation of bell pushbutton
1, with call signalling.

Summary of Contents for DoorLine TM4





















































Search results

Summary of Contents for DoorLine TM4

Reviews:

Related manuals for DoorLine TM4

Brands by name

Popular brands

Telegärtner DoorLine TM4, Operating And Assembly Instructions Manual

Search results

Summary of Contents for DoorLine TM4

Reviews:

Related manuals for DoorLine TM4

Brands by name

Popular brands