manualshive.com logo in svg

Teledyne T101, Operation Manual, Page: 24 / 375

Share
Download
Teledyne T101 Operation Manual Download Page 24

Introduction 

Teledyne  ML  – T101 Operation Manual 

20 

  

1.2.

 

OPTIONS 

The options available for your analyzer are presented in Table  1-1  with name, option 
number, a description and/or comments, and if applicable, cross-references to technical 
details in this manual, such as setup and calibration. To order these options or to learn 
more about them, please contact the Sales department of Teledyne Monitor Labs at: 

TOLL-FREE: 

800-846-6062 

TEL: 

+1 303-792-3300 

FAX: 

+1 303-799-4853 

E-MAIL: 

[email protected] 

WEB SITE: 

http://www.teledyne-ml.com/ 

 

Table 1-1. Analyzer Options 

Option 

Option 

Number 

Description/Notes 

Pumps 

 

Pumps meet all typical AC power supply standards  while exhibiting 

same pneumatic  performance. 

 

10A 

External Pump 100V - 120V @ 60 Hz 

10B 

External Pump 220V - 240V @ 50 Hz 

10C 

External Pump 220V - 240V @ 60 Hz 

10D 

External Pump 100V – 12V @ 50 Hz 

10E 

External Pump 100V @ 60 Hz 

11A 

Pumpless (if one is standard  either internal or external) 

13 

High Voltage Internal Pump 240V @ 50Hz 

Rack Mount 

Kits 

 

Options for mounting the analyzer in standard 19” racks 

 

20A 

Rack mount brackets with 26 in. chassis slides 

20B 

Rack mount brackets with 24 in. chassis slides 

21 

Rack mount brackets only (compatible with carrying strap, Option 29) 

23 

Rack mount for external pump pack (no slides) 

Carrying Strap/Handle 

Side-mounted  strap for hand-carrying analyzer 

 

29 

Extends from “flat” position to accommodate hand for carrying. 
Recesses to 9mm (3/8”)  dimension for storage. 
Can be used with rack mount brackets, Option 21. 
Cannot be used with rack mount slides. 

 

 

CAUTION 

GENERAL SAFETY HAZARD 

A FULLY  LOADED  T101  WITH VALVE OPTIONS WEIGHS >20 KG (45 
POUNDS). 

To avoid personal injury we recommend that two persons lift and carry the 

analyzer. Disconnect all cables and tubing from the analyzer before moving it. 

Analog Inputs 

Used for connecting external voltage signals from other instrumentation (such 

as meteorological instruments). 

 

64 

Also can be used for logging these signals in the analyzer’s internal DAS 

Summary of Contents for T101
























































































































































































































































































































































































Reviews:

No comments