manualshive.com logo in svg

Teledyne PS200 Series, Operation & Maintenance Manual, Page: 45 / 58

Share
Download
Teledyne PS200 Series Operation & Maintenance Manual Download Page 45

PS200

PORTABLE GAS MONITOR

RECHARGING THE BATTERIES

64171, Rev. 11/December 2019

7-1

7. RECHARGING THE BATTERIES
7.1. General

Use only approved chargers to recharge monitor.

The battery should be recharged when:
• ‘LOW BATTERY’ or ‘BAT FAULT’ appears on the display.
• The monitor will not switch on.

7.2. Recharge Monitor Using the Charging / Comms Clip

1. Connect the supplied Charging / Comms Clip to the monitor. Ensure the locating tongue on the

clip engages with the monitor locating slot and is firmly seated (refer to 

Figure 7-1:

Charging/Comms Clip Connection

).

Figure 7-1: Charging / Comms Clip Connection

2. Connect the supplied MINI-USB to USB Cable to the Charging / Comms Clip.

WARNING: CHARGING IS ONLY PERMITTED IN A NON-HAZARDOUS AREA.

CAUTION: Switch the monitor off when charging.

Contact Pads (x4)

Charging / Comms Clip (P/N 64260)

Locating Slot

Locating Tongue

Summary of Contents for PS200 Series



























































Reviews:

No comments