Teledyne PS200 Series Operation & Maintenance Manual Download Page 28 | Manualshive

Page: 28 / 58

Teledyne PS200 Series Operation & Maintenance Manual Download Page 28

PS200

PORTABLE GAS MONITOR

OPERATION

64171, Rev. 11/December 2019

3-8

6. MAX/MIN readings can be reset by pressing and holding the R button for 2 seconds when either

of the MAX/MIN screens are displayed.
After resetting, the monitor will return to the normal operating screen.
MAX/MIN/STEL/LTEL will be automatically reset during warmup, if the monitor is configured for

multi users.

3.6. Manual Datalog

Press the L button once to manually store the current gas readings. LOGGING appears on the

monitor as shown in

Figure 3-15: Manual Datalog

3.7. Alarms Reset or Acknowledge

When the monitor reaches an alarm set point, the audible, visual, and vibrating alarms will be acti

-

vated to alert the user.
Alarms are individually programmable to be either:
• Latching - alarms are active until the user resets by pressing and holding the R button after the

gas readings have returned to a safe level.

• Non-Latching - alarms will reset automatically when the gas readings have returned to a safe

level.

The audible alarm on each pre-set alarm can be muted for 60 seconds by pressing and holding the

R button. After this time, should the gas value remain out with the pre-set alarm limit, the non-latch

-

ing audible alarm will become active again. If latching, the audible alarm will become active again

regardless of gas value.

3.7.1. CONFIDENCE SIGNAL
During normal operation, the monitor sounds a confidence beep and illuminates the green LED’s

briefly every 15 seconds. This function informs the user that the monitor is operating correctly.

NOTE: The operation of the confidence beep and/or LEDs is configurable.

«
...
26
27
28
29
30
...
»

Summary of Contents for PS200 Series



























































Reviews:

No comments