manualshive.com logo in svg

Teledyne MagnaStar C-2000, User Manual, Page: 58 / 100

Share
Download
Teledyne MagnaStar C-2000 User Manual Download Page 58

44

(Rev. 8/04)

®

VI. Configuration Procedures

The Setup option on the main menu gives the user the ability to vary
some aspects of the system configuration. Some of these require the
entry of a passcode to prevent unauthorized access.

Note: Those functions which are denoted as System Functions apply to the entire 

C-2000 system and can be programmed from any single MagnaStar handset.

A. Station Configuration at a Glance

The user can access these menus by taking the handset off-hook,
pressing “9” (Setup) -“3” (Info), and then continue to press the “+”
key to select each successive menu.

(Factory Default)

“Station Setup”

‘Cabin’

“Ringer”

‘Enabled’

“Call Waiting is ‘Enabled’ -or- ‘Disabled’”

‘Enabled’

“Direct Call Pick-up is ‘Enabled’ -or- ‘Disabled’”

‘Enabled’

“Aircraft Number Alerting is ‘Enabled’ -or- ‘Disabled’”

‘Enabled’

“Auto Link Switch is ‘Enabled’ -or- ‘Disabled’”

‘Enabled’

“Station Default Baud Rate”

9600 bps

“Modem Call Handoff is ‘Enabled -or- ‘Disabled’”

4800 bps ‘Disabled’

9600 bps ‘Enabled’

“OCXO Cal. Factor: +/- xxx Hz”

(current OCXO Calibration Factor)

“RSS: - xxxdB”

(Current Receive Signal Strength of Ground Station)

“ARTU Serial Number”

(Assigned serial number “MSA-xxxx”)

“Elapsed Time Indicator”

(Current elapsed powered up time in minutes)

NOTE 1: The Factory defaults listed above are applied to software version 4.0A

and later.

NOTE 2: While in Remote Program mode for the CDBR-2, the station type (i.e.

Voice, Fax, Modem or PC) is displayed, as well as the CDBR’s software
version.

NOTE 3: The features that are disabled by default (see Factory Default above) must

be enabled by an Installer who has access to the Maintenance Passcode.

Summary of Contents for MagnaStar C-2000





































































































Reviews:

No comments