Teledyne HDO9000 Operator'S Manual Download Page 138

Page: 138 / 188

HDO9000 High Definition Oscilloscopes Operator's Manual

Setting Up WaveScan

This procedure explains how to set up WaveScan to search an acquisition for events of interest. Set

up your source channel and triggers before setting up the scan.

1. Press the front panel

Stop button

to stop acquisition.

2. Choose

Analysis > WaveScan

3. Check

Enable

4. Choose the

Source

waveform.

5. Choose the

Scan Mode

and enter values for any additional settings that appear at the right of

the dialog based on your selection.

6. If you're using Measurement Mode, set up the filter in one of the following ways:

Touch

Filter

and choose an operator, then enter the

Filter Limit

Touch

Filter Wizard

and choose one of the pre-set filters. The Filter and Filter Limit are

automatically set based on your selection.

7. Select each

Scan View

in which you wish to display results by checking the box at the bottom

of the dialog. Each view selected is displayed simultaneously.

8. If you're using Scan Overlay view, on the Scan Overlay dialog

Clear Sweeps

. If desired, set up

the

Persistence

display.

9. Optionally, choose an

Action

to trigger when an event that meets your scan criteria is found.

10. Restart acquisition.

11. When using the Zoom view, use the Z

tab to adjust the zoom.

Scan Overlay

To apply monochromatic persistence to a Scan Overlay:

1. Select

Scan Overlay

when setting up the wave scan, then open the

Scan Overlay dialog

2. Check

Persistence On

3. Enter a

Saturation

level as a percentage. All samples above the saturation level are assigned

the highest color intensity.

4. Choose a

Persistence Time

. The higher the time, the more static the persistence display.

To adjust the scan overlay to "zoom" in or out: touch the

In/Out buttons

, or touch

Scale

and enter new

values. Check

Var.

to adjust scale in finer steps than the default 1, 2, 5.

128

Summary of Contents for HDO9000





























































































































































































Search results

Summary of Contents for HDO9000

Reviews:

Brands by name

Popular brands

Teledyne HDO9000, Operator'S Manual

Search results

Summary of Contents for HDO9000

Reviews:

Brands by name

Popular brands