Teledyne HASTINGS Everywhereyoulook 201 Series Instruction Manual Download Page 10

141-072011 - 201/203 Series

 

Page 10 of 23 

the ground connection at the power supply. Do not connect them together at the flow controller as 
the resulting crosstalk could result in flow instabilities.  

24 Volt Connections 

Refer to the diagram at right when connecting 24 Volt 
units. 

Connect the positive lead of the power supply to pin 7 of 
the DE-9 connector and negative lead to pin 4.  The 
supply input is diode protected such that reversing the 
input polarity will not damage the instrument.   The 
power supply is galvanically isolated from all other pins.  

General Connection Notes 

Pin 7 of the DA-15 (15 Volt), Pin 9 of the DE-9 (24 Volt) 
is the case ground.   It should be connected to the cable 
shield if available and to the AC ground to the power 
supply. 

Pin 6 of the DA-15 (15 Volt), Pin 2 of the DE-9 (24 Volt) 
is the output signal from the flow controller. This output 
will be 0-5VDC/(4-20 mA), 5VDC/20mA being 100% of 
rated or full flow. Pin 14 of the DA-15 (15 Volt), Pin 3 of 
the DE-9 (24 Volt) is the command input. This should be 

a 0-5VDC or (4-20 mA) signal and must be free of spikes 
or other electrical noise, as these will generate false flow 
commands that the controller would attempt to flow. Pin 
15 of the DA-15 (15 Volt), Pin 1 of the DE-9 (24 Volt) is 
a reg5.00VDC output reference that is normally adjusted to 5.01VDC so that the user can 
achieve full scale command set point. The reference is designed to provide the command signal for 
pin 14 by connecting one end of a potentiometer to the voltage reference and the other end to 
ground. The center lead would then be connected to setpoint input. 

If a valve override switch is not desired, the unit is ready for use at this time. If the override switch is 
desired, connect the center pin of a single pole, three-position switch with the center off position to 
pin 8 of the DA-15 (15 Volt), Pin 6 of the DE-9 (24 Volt). Connect a voltage source >10 VDC to 

one end of the switch, and negative voltage to the other end. This will result in the valve being full 
open when the positive is supplied to the override pin, off when the negative voltage is supplied and 
auto-control when there is no connection to the valve override pin (OPEN-AUTO-CLOSE). This 
setup will be adequate for most purposes, but there will be a small delay for capacitors to charge 
between switch operation and control override. 

2.6. Operation 

The standard instrument output is a 0 - 5 VDC out and the signal is proportional to the flow i.e.,    0 
Volts = zero flow and 5 Volts = 100% of rated flow.  The 4 - 20 mA option is also proportional to 
flow, 4 mA = zero flow and 20 mA = 100% of rated flow. It is suggested that all connections be 

checked for leaks after installation. This can be done by pressurizing the instrument (do not exceed 
500 psig unless the instrument is specifically rated for higher pressures) and applying a diluted soap 
solution to the connections. 

2.6.1. Operating 

Conditions 

  For proper operation, the combination of ambient temperature and gas temperature must be such 
that the flow meter temperature remains between 0 and 50°C.  (Most accurate measurement of flow 
will be obtained if the flow meter is zeroed at operating temperature as temperature shifts result in 

Summary of Contents for HASTINGS Everywhereyoulook 201 Series
























Reviews: