manualshive.com logo in svg

Teledyne Everywhereyoulook CCD261-04, Quick Start Manual, Page: 12 / 12

Share
Download
Teledyne Everywhereyoulook CCD261-04 Quick Start Manual Download Page 12

 

 

© Teledyne UK Limited 2020 

Document subject to disclaimer on page 1 

A1A-795787 Version 1, page 12 

 

 

ORDERING INFORMATION 

CCD261-04-g-xxx 

g = cosmetic grade 

xxx= specific variant type (e.g. thickness and coating) 

 

CCD261-04-g-S31:  Deep Depleted Silicon, NIR AR 

coating 

 

 

For further information on the performance of this 

and other options, please contact Teledyne e2v. 

 

HANDLING CCD SENSORS 

CCD sensors, in common with most high 

performance MOS IC devices, are static sensitive. In 

certain cases a discharge of static electricity may 

destroy or irreversibly degrade the device. 

Accordingly, full antistatic handling precautions 

should be taken whenever using a CCD sensor or 

module. These include:- 

•

  Working at a fully grounded workbench 

•

  Operator wearing a grounded wrist strap 

•

  All receiving socket pins to be positively 

grounded 

•

  Unattended CCDs should not be left out of 

their conducting foam or socket. 

Evidence of incorrect handling will invalidate the 

warranty.  

 

HIGH ENERGY RADIATION 

Device characteristics will change when subject to 

ionising radiation. 

Users planning to operate CCDs in high radiation 

environments are advised to contact Teledyne e2v. 

 

TEMPERATURE LIMITS 

 

Min  Typical  Max 

Storage ............................. 148 

- 

323  K 

Operating .......................... 223 

263 

293  K 

Operation or storage in humid conditions may give 

rise to ice on the sensor surface on cooling, causing 

irreversible damage. 

 

Maximum device heating/cooling

 ................. 5 K/min 

 

Summary of Contents for Everywhereyoulook CCD261-04













Reviews:

No comments