manualshive.com logo in svg

Teledyne ADQ8-4X, Manual, Page: 6 / 46

Share
Download
Teledyne ADQ8-4X Manual Download Page 6

19-2302 A 
2020-09-16

6(46)

ADQ8-4X Manual

19-2302 A 2020-09-16

6(46)

The number representation is 2’s complement. The full scale maximum code is then 32 704 and the full 
scale minimum code is –32 768. Overflow or underflow at any position in the signal path will saturate 
the data and turn on an overflow flag. See 

Section 7.10

 for more information on over- and under-flow. 

1.2.2

Calibration

During the factory calibration procedure the analog properties are measured and parameters for a digi-
tal compensation are computed. An analog deviation in the front-end is thus compensated for by the 
inverse function in the digital signal processing part. 

Example 1: With the variable gain –VG option (always included with the ADQ8-4X), the user requests 
a range. The closest available setting is selected and the actual range is returned to the user for being 
used in the user’s algorithms, see 

Section 2.1

. 

Example 2: The full scale signal range of the ADQ is measured in production and the 

SetGainAndOff-

set

 function is used for adjusting to the correct signal range. 

1.2.3

Data acquisition nomenclature 

Table 1

 defines some key data acquisition terms. 

1.2.4

Sampling clock frequency

The ADQ8-4X is designed for the specified 2 GHz clock frequency only with the firmware FWDAQ. The 
firmware FW4GDAQ enables sampling at 4 GSPS. A different sampling rate can be achieved by using 
the sample skip function, 

Section 5.10

.

1.2.5

System clocks 

The different parts of the digitizer operate on different clock rates
The sampling of the analog signal is done on the sampling clock of the ADC (see 

Section 1.2.4

). 

The external trigger input has a trigger clock which is higher than or equal to the sampling clock for high 
trigger time precision (4 GHz). This clock frequency is the same regardless of selected sampling fre-
quency. 
The PCIe host PC connections has its own clock system. 

Table 1:   Data recording nomenclature. 

PARAMETER

DESCRIPTION

REF

ADQ

Collective name for digitizers from Teledyne SP Devices.

Analog

Analog signal is the input to the digitizer. This is the signal to be digitized. 

Waveform

Analog signal with a distribution in time. This is digitized into a record. 

Sample

An analog signal level is digitized into a sample, that is a numerical value. 

SYNC

Physical connector on the front panel.

4.8

, 

6.1

Record

A set of consecutive samples is called a record. An analog waveform is 
digitized into a record of samples. 

4

TRIG

Physical connector on the front panel.

4.8

, 

6.1

Trigger

Trigger is an event that starts acquisition of a record. 

4.3

Timestamp

Timestamp is a real-time value that identifies when a trigger happened. 
The timestamp gives timing information for each sample. 

4.4

GSPS

Giga-samples per second (10

9

). Clock frequency [Hz] and sample rate 

[SPS] are both used to denote speed. 

MSPS

Mega-sample per second (10

6

). 

DC-offset

This is an analog DC level which is added to the analog input signal inside 
the digitizer to vertically move the analog signal to fit within the range of 
the digitizer. This effectively doubles the ENOB for a unipolar signal. 

2

Summary of Contents for ADQ8-4X















































Reviews:

No comments