manualshive.com logo in svg

Teledyne Lecroy AP015, Operator'S Manual

Share
Download
Teledyne Lecroy AP015 Operator'S Manual Download Page 12

Distributor of Teledyne LeCroy: Excellent Integrated System Limited

Datasheet of CP015-CF01 - HIGH SPEED CURRENT SHUNT CP015 
Contact us: [email protected] Website: www.integrated-circuit.com

Operator’s Manual 

922254-00 Rev A 

7 

Performance Verification Procedure 

The warranted characteristics of the AP015 Current Probe are valid at any 
temperature within the Environmental Characteristics listed in the 
Specifications. However, some of the other test equipment used to verify the 
performance may have environmental limitations required to meet the accuracy 
needed for the procedure. Make sure that the ambient conditions meet the 
requirements of all the test instruments used in this procedure. 

NOTE

: The correct operation of the controls of the AP015 requires oscilloscope 

software version 7.6.0 or higher for LT series scopes. The use of earlier versions 
is not recommended. The software version in the LT series test oscilloscope can 
be verified by pushing SHOW STATUS, then selecting the System menu option. 
Contact your local Teledyne LeCroy representative if the software in your 
oscilloscope requires updating. 

A. Check Bandwidth 

1.

 

Set the Leveled Sine Wave Generator frequency to 50 kHz, the output 
level to approximately 5 Vp-p (+18 dBm), and turn RF ON. 

2.

 

Connect the output to the BNC connection of the high-speed shunt 
calibration fixture, AP015-CF02, using the matched BNC coaxial cable 
specified for use with the leveled sine wave generator. 

3.

 

Open the slider and connect the AP015 to the high-speed shunt 
calibration fixture. Close and lock the probe slider by pushing it fully 
away from the probe cable. 

4.

 

Push the AUTO SETUP button on the oscilloscope. Press MEASURE 
TOOLS, set the mode to Std Voltage, on trace 1, from 0.00 div to 10.00 
div. 

5.

 

Adjust the generator level until the current is 100 mA peak-to-peak, as 
measured using the peak-to-peak function on the oscilloscope. 

6.

 

Set the sine wave generator frequency to 25 MHz. Be careful not to alter 
the signal amplitude. 

7.

 

Slowly increase the output frequency until the displayed amplitude of 
the current sine wave decreases to 71 mA peak-to-peak (a 3 dB 
reduction in amplitude). 

                            12 / 25

                            12 / 25

Summary of Contents for AP015


























Reviews:

No comments

Brands by name

Popular brands

Load more brands