CONNECTING THE IPHONE A SERIES
1. Located on the left side of the iPhone (as the phone is facing you) is a modular jack. Insert one end of the coiled handset cord
into this jack (you should hear the coil cord click when properly inserted).
2. Insert the other end of the coiled handset cord into the modular jack on the handset.
3. Turn the telephone so the back panel is facing you. Insert either end of the line cord into the jack on the back of the
telephone labeled LINE.
4. Insert the other end of the line cord into a telephone wall outlet jack.
5. Once your telephone is connected, remove the plastic overlay and place the paper face plate over the keys. Replace the
plastic overlay by hooking the tabs on the overlay into the recessed slots located on both sides.
PLACING A CALL USING THE HANDSET
1. Lift the handset. The “LINE” LED will illuminate. (On two-line models, if both lines are inactive, line 1 will be activated. If one
of the two lines is active, the inactive line will be activated.)
2. Listen for dial tone. Dial the desired number, or press an AUTO DIAL key to automatically dial a number.
3. To end the call, hang up by placing the handset back in the cradle.
PLACING A CALL USING THE SPEAKERPHONE
(APPLIES ONLY TO MODELS WITH INCLUDED SPEAKERPHONE)
1. With the handset in the cradle, press either the SPEAKER key or the LINE key (on two-line models, select either inactive LINE
key). The telephone will go offhook on the selected line with speakerphone active.
2. Listen for dial tone, and dial the desired number, or press an AUTO DIAL key to automatically dial a number.
3. To end the call, press the SPEAKER key.
RECEIVING A CALL
TO ANSWER A CALL USING THE HANDSET:
1. Lift the handset. On two-line models, if one line is already in use, the iPhone will automatically select the ringing line.
2. To end the call hang up the handset.
TO ANSWER A CALL USING THE SPEAKERPHONE
1. With the handset in the cradle, press the line key associated with the ringing line.
The iPhone will asnwer the line selected with the speakerphone active. You may also:
2. Press the SPEAKER key. The iPhone will select the ringing line and answer with the speakerphone active.
NOTE: THE RED SPEAKER LED WILL INDICATE THAT THE SPEAKERPHONE IS ACTIVE.
CONFERENCE
(TWO-LINE-MODELS ONLY)
On two-line telephones, the CONFERENCE key allows the user to include two other parties in a three-way conversation. After
placing or receiving a call to/from the first party, place that party on hold by pressing the HOLD key. Using the second line, place
or receive the second call. Press the CONF key to join all three callers.
ADJUSTING THE SPEAKERPHONE VOLUME
To the left of the dialpad, locate the volume up/down arrow keys. With the speakerphone active, press either the up or down
key to raise or lower speaker volume to the desired level.
ADJUSTING THE RING VOLUME
On the rear panel of the telephone, locate the ringer volume slide swtich. There are three settings: Low, high, and crescendo.
The crescendo setting is indicated by a small triangular icon. Set the switch to the desired setting.
By selecting the crescendo ringer setting, the phone will first ring at its lowest volume. With each successive ring, ringer volume
will increase slightly, until, by the fourth ring, ringer volume is at the highest level. Each successive incoming call will begin at
the lowest ring volume and ring accordingly.
USING THE SPEAKERPHONE
(SPEAKERPHONE-EQUIPPED MODELS ONLY)
If you are talking on the handset and wish to transfer to the speakerphone, press the SPEAKER/HSET key, and hang up the hand-
set in the cradle. The speakerphone will now be active.
If you are talking on the speakerphone and wish to transfer to the handset, pick up the handset from the cradle. The speaker-
phone LED will go out and the call can be continued on the handset.
USING THE HOLD KEY
(TWO-LINE MODELS ONLY)
TO PLACE A CALL ON HOLD
1. With a call active, press the HOLD key.
2. The red line LED will change to a slow blink indicating the call is on hold.
2
