manualshive.com logo in svg

Teldat H2 RAIL, Installation Manual, Page: 10 / 47

Share
Download
Teldat H2 RAIL Installation Manual Download Page 10

Switch and Ethernet WAN LED indicators

LED

Associated Interface

Description

Yellow

LAN 1..4 and Eth WAN

OFF -> Interface is unavailable, not installed or not re-
gistered.

ON -> Connected to 10 M:

- Steady: Is not transferring data.

- Blinking: Transferring data.

 Green

LAN 1..4 and Eth WAN

OFF -> Interface is unavailable, not installed or not re-
gistered.

ON -> Connected to 100 M:

- Steady: Is not transferring data.

- Blinking: Transferring data.

Green

LAN 1..4 and Eth WAN

OFF -> Interface is unavailable, not installed or not re-
gistered.

ON -> Connected to 1000 M:

- Steady: Is not transferring data.

- Blinking: Transferring data.

3.1.2 Rear panel

The following figure shows the rear panel.

Fig. 2:

Rear panel

The rear panel components are as follows:
Rear panel components

Item

Description

A

Functional earthing. Usually not connected.

B

12-24 DC. Power source connection.

C

LEDs:

• On: Illuminated indicator showing whether the device is switched on or not.

• A, B and C: explained in rear panel LEDs table.

D

W1, W2. WiFi antennas for the Wireless LAN module. This module is optional
(your device may not have any antennas).

E

C1, C2. Antennas for the Teldat H2 Automotive cellular module. This module is

Teldat S.A.

3 Components and Power Supply

Teldat H2 Automotive Router

5

Summary of Contents for H2 RAIL
















































Reviews:

No comments