manualshive.com logo in svg

Tektronix TLA7000 Series, Installation Manual

Share
Download
Tektronix TLA7000 Series Installation Manual Download Page 86

Merging Modules

Merge the

fi

rst Slave module to the Master module. (See page 63,

Two-Way Logic

Analyzer Merge Procedure

.)

Perform the following steps to merge the second slave module:

1.

Lay the two merged module set on its right side (as viewed from the front
panel).

2.

Repeat the procedure to merge the second slave module.

Storing the Logic Analyzer

Module Merge Cable

Perform the following steps to store the logic analyzer merge cable inside the
logic analyzer module:

1.

Use the screwdriver with the T-10 Torx tip to remove the screws that hold the
merge cable bracket in place.

2.

Remove the merge cable bracket.

3.

Remove the screws from the side cover and rear cover.

4.

Push the merge cable through the side cover and remove the cover.

5.

Position the merge cable. (See Figure 56.)

Figure 56: Positioning the merge cable before installing the cover

68

TLA7000 Series Logic Analyzers Installation Manual

Summary of Contents for TLA7000 Series


























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands