Tektronix THDP0100 Installation And Safety Instructions Download Page 29 | Manualshive

Page: 29 / 30

background image

Controls and Features

Controls and features

Item

Description

Bandwidth Limit button and indicators

Press the button to limit the probe
bandwidth to 5 MHz. The 5 MHz

fi

lter

assists in the characterization and
testing of power supplies in switch

mode by removing all high frequency
content, noise and harmonics from the
measurement. 5 MHz is close to the
switching frequency of most switching
transistors (FETs) in switch-mode power
supplies.
Press the button again to return to the
FULL position, which selects the full
speci

fi

ed bandwidth of the probe.

Audible Overrange On/Off button and
indicators

The audible alarm beeps when the
measured signal exceeds the selected
range. Press the button to disable the
audible feature (the OFF LED lights).
Press the button again to enable the
audible alarm (the ON LED lights).

27

«
...
27
28
29
30
»

Summary of Contents for THDP0100































Reviews:

No comments

Related manuals for THDP0100

Brand: Raymarine Pages: 55

Brand: Halyard Pages: 4

Underwater Light Show & Fountain

Brand: GAME Pages: 2

Brand: Napoleon Pages: 2

Brand: Raytheon Pages: 62

WJHD100 - DIGITAL DISC RECORDE

Brand: Panasonic Pages: 7

Brand: FEAS Pages: 72

Brand: Bante Instruments Pages: 6

Brand: Cameo Pages: 64

Brand: Cameo Pages: 100

Brand: CAME Pages: 32

Brand: made for movement Pages: 51

Brand: Patlite Pages: 28

Web Ankle Brace

Brand: Darco Pages: 2

Brand: Darkly Labs Pages: 13

Brand: DARAY Pages: 24

Body Armor Night Splint

Brand: Darco Pages: 2

Brand: LaboGene Pages: 59

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands