www.tektronix.com
Calibrating the Touch-Screen Display
You must calibrate the touch-screen display to
respond correctly to your taps before using the
NetTek Analyzer.
1
.
Select
Start > Settings > Control Panel
.
2
.
Open (double-tap) the Stylus icon.
3
.
In the
Double-Tap
tab, double-tap the
checkerboard grid at a comfortable speed with a
stylus or your finger. This sets the tap rate
sensitivity.
4
.
Select the
Calibration
tab.
5
.
Follow the on-screen instructions to set the
touch-screen location and pressure values. Apply
pressure to the touch-screen for approximately
5 seconds to register each tap.
6
.
Tap
OK
to close the dialog box.
7
.
Restart the NetTek Analyzer to save and apply the
touch-screen calibration settings.
Online Help
To access Windows CE online help, select
Start > Help
.
For NetTek Analyzer-specific help, select
Start >
Help > Windows CE Basics > Tektronix NetTek
Analyzer Platform Basics
.
Some application windows have context-sensitive
help, as indicated by a question mark icon at the top
of the application screen. Selecting the context-sensi-
tive icon displays information about the active
application window.
Transportation and Lithium-Ion Batteries
Each Y400 lithium--ion battery pack contains less
than 8 grams of lithium, with individual cells each
containing less than 1.5 grams of lithium, as
measured by International Civil Aviation Organiza-
tion (ICAO) standards. Consult your air carrier for
applicability and determination of any special
lithium--ion battery transportation requirements.
Cleaning
1
.
Disconnect the NetTek Analyzer from the external
power adapter.
2
.
Close all NetTek Analyzer connector and battery
doors.
3
.
Install the bus door on the NetTek Analyzer or
application module.
4
.
Use a soft cloth dampened with a solution of
water and mild detergent. Do not immerse the
analyzer or use abrasive cleaners.
CAUTION
.
To prevent damage to external
surfaces, do not use chemicals that contain
acetone, benzene, toluene, xylene, or similar
solvents. Do not use bleach or ammonia
solutions for cleaning.
Contacting Tektronix
Web site:
www.tektronix.com
Phone:
1--800--833--9200
Address:
Tektronix, Inc.
Department or name (if known)
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
Email:
Additional contact information is also located on the
online help system by selecting
Start > Help >
Windows CE Basics > Tektronix NetTek Analyzer
Platform Basics > Contacting Tektronix
.
For more information on the NetTek Analyzer,
including options and accessories, go to
www.tektronix.com and enter
Y400
in the web page
search field.
EMC Compliance
EC Declaration of Conformity -- EMC
Meets intent of Directive 89/336/EEC for Electromagnetic
Compatibility. Compliance was demonstrated to the following
specifications as listed in the Official Journal of the European
Union:
EN 61326
EMC requirements for Class A electrical
equipment for measurement, control and
laboratory use.
1,2,3,4
IEC 61000-4-2
Electrostatic discharge immunity
(Performance criterion B)
IEC 61000-4-3
RF electromagnetic field immunity
(Performance criterion A)
IEC 61000-4-4
Electrical fast transient/burst immunity
(Performance criterion B)
IEC 61000-4-5
Power line surge immunity
(Performance criterion B)
IEC 61000-4-6
Conducted RF immunity
(Performance criterion A)
IEC 61000-4-11
Voltage dips and interruptions immunity
(Performance criterion B)
EN 61000-3-2
AC power line harmonic emissions
EN 61000-3-3
Voltage changes, fluctuations, and flicker
Australia/New Zealand Declaration of Conformity -- EMC
Complies with EMC provision of Radiocommunications Act per
the following standard(s):
2,3
AS/NZS 2064.1/2
Industrial, Scientific, and Medical
Equipment: 1992
1
Platform EMC performance may be altered when operated
with an application module; EMC specifications for the
application module apply in that case.
2
EMC compliance was demonstrated using high-quality
shielded interface cables.
3
Emissions that exceed the limits of this standard may occur
when the instrument is connected to a test object.
4
Minimum Immunity test requirement.
Y400
NetTek
r
Analyzer
Setup Reference
*P071143000*
071-1430-00
