Tektronix Keithley 4299-2 Dual-Unit Installation Instructions Manual Download Page 4

Page: 4 / 12

Model 4299-2 Dual-Unit Rack-Mount Kit Installation Instructions

PA-909 Rev. J April 2021

Install mounting hardware

Install the mounting hardware on the opposite sides of each instrument, as shown in the following figures.

To install the mounting hardware on the instruments:

1. Place the instruments side-by-side, in the same position that they will be installed in the rack.
2. Secure one rear rack-mount bracket (2602-334) to each instrument on the selected side using two Phillips

pan-head SEMS screws (#10-32 × 3/8 PPHSEM).

If the two instruments are not the same length, do not use one of the rear rack-mount brackets. Refer
to

Install the instruments

(on page 9), "To install two instruments that are of unequal length" for more

detail. Additionally, save all unused parts for future use.

Figure 4: Rear rack-mount bracket

Summary of Contents for Keithley 4299-2 Dual-Unit













Search results

Summary of Contents for Keithley 4299-2 Dual-Unit

Reviews:

Related manuals for Keithley 4299-2 Dual-Unit

Brands by name

Popular brands

Tektronix Keithley 4299-2 Dual-Unit, Installation Instructions Manual

Search results

Summary of Contents for Keithley 4299-2 Dual-Unit

Reviews:

Related manuals for Keithley 4299-2 Dual-Unit

Brands by name

Popular brands