Tektronix DPO2304SX Printable Help Download | Manualshive

Page: 677 / 920

background image

Using the programmer online guide

Programmer online help

You can control the instrument via GPIB (on some instruments), from a remote PC, or from an Internet or Intranet connection.
Programming information is available as a separate file you can install.

Using application software

Oscilloscope applications software

You can install and run optional application software packages on the instrument. These software packages provide advanced
capabilities that support several applications, such as jitter analysis and disk drive measurements.

Each application can be purchased and installed on the instrument at any time. Contact your Tektronix representative for
purchasing information. Follow the installation instructions that come with the application.

To open your application software on the instrument, click Analyze in the menu bar, and then select the application to run.

NOTE. Application software packages have their own online help that is separate from the main instrument online help.

Add a software application to the instrument

Because the instrument is an open Windows platform, you can easily install and remove additional software applications. Follow
the instructions that came with your software and the basic Windows instructions to install and remove your application.

NOTE. When adding software to the instrument, avoid making changes to system files. See

Windows Interface

for more

information.

Setting up a dual display

Set up a dual display

Use the following steps to set up the instrument for dual display operation. You can use the main display for most instrument
operations while you use a second monitor to access other PC applications that you may have installed.

You can also drag up to five dockable control windows from the TekScope application onto the display of the second monitor.

For example, this feature allows you to have the Horizontal/Acquisition, the Horizontal Zoom, and the Display Setup Control
Windows (half screen) open on the second monitor at the same time.

In addition to the five dockable windows on the second monitor, you can have one dockable window open on the main display. If
you open a seventh dockable window, whichever window has not been used for the longest amount of time will automatically
close.

TIP. You may want to print this procedure since it requires you to power off the instrument.

1. Power off the instrument.

2. Connect an external monitor to a video port on the instrument.

3. Connect a keyboard and mouse.

4. Power on the instrument and external monitor.

How to ?

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

645

«
...
675
676
677
678
679
...
»

Summary of Contents for DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DPO2304SX

Brand: MAHLE Pages: 21

Brand: Rain Bird Pages: 2

Brand: Keithley Pages: 67

Brand: Keithley Pages: 23

Brand: Keithley Pages: 93

Brand: Oki Pages: 44

Brand: Magnescale Pages: 64

Brand: XanLite Pages: 4

Brand: T-Rex Pages: 13

PORTABLE ICE FISHING KIT

Brand: Garmin Pages: 5

Brand: Posture Pump Pages: 2

FLOOReco 5164-040120

Brand: DOTLUX Pages: 10

Brand: Aspect Medical Systems Pages: 104

Brand: Hupfer Pages: 153

Brand: Strapack Pages: 16

Brand: Hameg Pages: 60

Brand: Cuisinart Pages: 159

DJ Laptop stand +tray

Brand: Power Dynamics Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands