Tektronix DPO2304SX Printable Help Download | Manualshive

Page: 608 / 920

background image

Compensate passive probes

Use this procedure to optimize gain and offset accuracy at the probe tip. Allow the instrument to warm up before performing this
procedure.

Perform the

low frequency probe compensation

for passive probes.

NOTE. The probe compensation procedure is not recommended for the P5050 passive probes. These probes have little gain or
offset errors. However, you should perform this procedure for other passive probes.

Complete the following steps:

1. If you have not already done so, connect the probe to the instrument.

2. Connect the probe to probe compensation (Fast Edge on some models) terminals as shown. Connect only one probe at a

time.

3. Select Probe Cal from the Vertical menu to open the Probe Compensation control window.

4. Select the channel to which the probe is attached.

5. Click Compensate Probe to begin the procedure. The Probe Status indicator changes to Pass when the procedure is

complete. If the procedure does not pass, contact your local Tektronix service personnel.

6. Remove the connections from the terminals.

Low frequency compensate a probe

Use this procedure to compensate passive probes to ensure maximum distortion-free inputs to the instrument.

1. Connect the probe to Ch 1 on the instrument.

2. Attach the probe tip and reference lead to the probe compensation terminals .

3. Press the Autoset button on the instrument.

4. Adjust the probe until you see a square wave with a perfectly flat top on the display.

5. See your probe manual for adjustment instructions.

Deskew

Use the following procedure to compensate for timing differences between voltage probes:

1. Set up the instrument to display all of the channels that you want to deskew.

2. Push the instrument Autoset button.

3. Adjust the vertical Scale and Position controls for each channel so that the signals overlap and are centered on the display.

4. Adjust the horizontal Position so that a rising edge is triggered at the center of the display.

5. Adjust the horizontal Scale so that the differences in the channel delays are clearly visible.

6. Adjust the horizontal Position again so that the first rising edge is exactly at the center of the display. The fastest probe is

connected to this channel (the fastest probe is usually the one with the shortest cable or with the highest bandwidth).

7. Select Deskew from the Vertical menu to open the Deskew control window.

How to ?

576

DPO70000SX, MSO/DPO70000DX, MSO/DPO70000C, DPO7000C, and MSO/DPO5000B Series

«
...
606
607
608
609
610
...
»

Summary of Contents for DPO2304SX

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for DPO2304SX

Brand: Makita Pages: 10

Brand: Hacker Pages: 2

Brand: J.P. SELECTA Pages: 8

Brand: Haemonetics Pages: 134

Brand: Hadeco Pages: 72

Brand: SandenVendo Pages: 19

Brand: Mach Pages: 12

Brand: Valcom Pages: 6

Brand: Vaisala Pages: 60

Brand: Yamaha Pages: 139

Brand: Yamaha Pages: 19

Brand: Yamaha Pages: 32

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...

Brand: M-Audio Pages: 25

Brand: Qlight Pages: 4

Brand: Qtx Pages: 6

Pendalyte 40472U

Brand: Lightolier Pages: 3

Brand: Marcy Pages: 9

Brand: VanGaa Lighting Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands