TM 9-6625-474-14&P-3
MAINTENANCE
GENERAL MAINTENANCE INFORMATION
Static-Sensitive Components
Static discharge can damage any
component in this instrument.
semiconductor
This instrument contains electrical components that
are susceptible to damage from static discharge See
Table 5-1 for relative susceptibility of various classes of
semiconductors. Static voltages of 1 kV to 30 kV are
common in unprotected environments.
Observe the following precautions to avoid damage:
1. Minimize handling of static-sensitive components.
2. Transport and store static-sensitive components or
assemblies in their original containers, on a metal rail, or
on conductive foam. Label any package that contains
static-sensitive assemblies or components.
3. Discharge the static voltage from your body by
wearing a wrist strap while handling these components.
Servicing static-sensitive assemblies or components
should be performed only at a static-free work station by
qualified service personnel.
4. Nothing capable of generating or holding a static
charge should be allowed on the work station surface.
5. Keep the component leads shorted together
whenever possible.
6. Pick up components by the body, never by the leads.
7. Do not slide the components over any surface.
8. Avoid handling components in areas that have a
floor or work surface covering capable of generating a
static charge.
9. Use a soldering iron that is connected to earth
ground.
10. Use only special antistatic suction type or wick
type resoldering tools.
Relative Susceptiblity to
Static Discharge Damage
equivalent for levels:
1 = 1oo to 500
V
4=500 V
7 = 400 to 1000 V (est.)
2 = 200 to 500
V
5 = 400 to 600 V
8 = 900 V
3 = 250 V
6 = 600 to 800 V
9 = 1200
V
(Voltage discharged from a 100 pF capacitor through a
resistance of 100 ohms.)
Cleaning
This instrument should be cleaned as often as
operating conditions require. Loose dust accumulated on
the outside of the instrument can be removed with a soft
cloth or small brush. Remove dirt that remains with a soft
cloth dampened in a mild detergent and water solution. Do
not use abrasive cleaners.
Summary of Contents for DC503a
