teko ASTRA-713 Operating Manual Download Page 3

Page: 3 / 52

This operating manual is intended for studying the operating principles, proper use, storage, and

maintenance of the control panel Astra-713.

Below is the list of abbreviations, used in this operating manual:

Equipment

Astra-713 Control Panel

Astra-Dozor

Astra-Dozor Control Panel

Astra-Z-8945

Astra-Z-8945 Control Panel

Relay

Programmable “dry-contact”-type relay output

Programmable “open collector”-type output

Sound Alerter

Light Alerter

Built-in Buzzer (beeper)

TM Key

Touch Memory identifier

Reader

TM key reader (for example, the Astra-TM reader)

Astra-RVC

Wireless receiver Astra-RVC ver. TM

Astra-TRC

Wireless transmitter Astra-TRC or Astra-TRC ver. M

Interface RS-485

Data exchange interface among external devices (units)

Adapter Astra-984

Interface adapter for connection to PC via RS-485

Personal (desktop) Computer

Firmware

CSP

Central Surveillance Post

Summary of Contents for ASTRA-713





















































Search results

Summary of Contents for ASTRA-713

Reviews:

teko ASTRA-713, Operating Manual, Page: 3 / 52

Search results

Summary of Contents for ASTRA-713

Reviews: