Teknim VAP Series User Manual Download Page 29

Page: 29 / 36

BD-1/07-002

For VPC016, VPC104, VPC108, VPC116 and VPC132 keypads;

For VPC301 keypad;

* All emergency buttons are active as factory default.

18.4. Sound Options

Warning Beeps of keypad can be disabled. Following table shows address of
warning beeps.

Beeps

Option

VPC108

VPC016,116

VPC132

VPC301

Exit delay beep

1.option

99 05

99 08

99 14

Keypad setting/Customize/

Sound Option

Arm beep

2.option

Alarm beep

3.option

Trouble beep

4.option

Button click

5.option

Confirmation beep

6.option

For VPC016, VPC104, VPC108, VPC116 and VPC132 keypads;

For VPC301 keypad

;

* All beeps are active as factory default.



Enter to the master program.

[Enter]

(Program) key long until you hear a long beep.

[Enter] Your 4 digit master code.



[Enter] Address by looking table above.



[Enter] Emergency button no you want to inactive.



[Enter]

(Ok) key.



Enter to the master program.

[Enter]

(Program) key long until you hear a long beep.

[Enter] Your 4 digit master code.



[Enter] Keypad setting/Customize/

Buttons

(select releted emergency button option).



[Enter] Emergency button no you want to inactive.



[Enter]

(Ok) key.



Enter to the master program.

[Enter]

(Program) key long until you hear a long beep.

[Enter] Your 4 digit master code.



[Enter] Address by looking table above.



[Enter] Options no you want to disable.



[Enter]

(Ok) key.



Enter to the master program.

[Enter]

(Program) key long until you hear a long beep.

[Enter] Your 4 digit master code.



[Enter] Keypad setting/Customize/Sound Option

(select releted sound button option).



[Enter] Options no you want to disable.



[Enter]

(Ok) key.

Summary of Contents for VAP Series





































Search results

Summary of Contents for VAP Series

Reviews:

Related manuals for VAP Series

Brands by name

Popular brands

Teknim VAP Series, User Manual

Search results

Summary of Contents for VAP Series

Reviews:

Related manuals for VAP Series

Brands by name

Popular brands