manualshive.com logo in svg

Teknik 5426135, Instructions Manual, Page: 27 / 33

Share
Download
Teknik 5426135 Instructions Manual Download Page 27

 å

Carefully stand your unit upright in its fi nal location. We recommend using the SAFETY STRAP for added stability.

 å

NOTE: Do not turn the SAFETY DRYWALL ANCHOR into a wall stud. If you prefer to fasten the SAFETY STRAP to a wall
stud, go to your local hardware store for proper hardware.

 å

INSTALLATION INSTRUCTIONS:
1. Insert the SAFETY DRYWALL ANCHOR through the WASHER and the end of the SAFETY STRAP.
2. Using a Phillips screwdriver or a hand drill, press the screw slightly onto the drywall.
3. Apply pressure; turn the screw until a pilot hole is made and the nylon sheath slips through.
4. Turn the screw until it is fl ush against the wall and you feel a fi rm resistance.
5. Continue to turn until the screw starts spinning freely.

 å

NOTE: Before moving your unit to a diff erent location, unscrew the SAFETY DRYWALL ANCHOR from your wall. The
nylon sheath will remain behind your wall.

Step 21

Safety 
drywall 
anchor

Safety strap

Washer

97

Page 27

Summary of Contents for 5426135


































Reviews:

No comments