manualshive.com logo in svg

Tekmar tekmarNet 532, Installation & Operation Manual

Share
Download
Tekmar tekmarNet 532 Installation & Operation Manual Download Page 19

© 2015 

 532_D - 02/15

19 of 20

A Watts Water Technologies Company

Technical Data

tekmarNet

®

 Thermostat 532 

One Stage Heat

Literature

532_C, 532_D, 532_Q, 532_U

Control

Microprocessor control. This is not a safety (limit) control.

Packaged weight

0.53 lb. (240 g)

Dimensions

3-11/16

"

 H x 3

"

 W x 15/16

"

 D (94 x 76 x 24 mm)

Enclosure

White PVC plastic, NEMA Type 1

Approvals

Meets Class B: ICES & FCC Part 15

Ambient conditions

Indoor use only, 32 to 122°F (0 to 50°C), RH ≤90% non-
condensing

Power supply

24 V ± 10%, 50/60 Hz, 1.8 VA standby, Class 2

Relays

24 V (ac/dc), 2 A, Class 2 circuits

Sensor

NTC thermistor, 10 kΩ @ 77°F (25°C ±0.2°C) ß=3892

– Included

None

– Optional

tekmar type # 070, 072, 073, 076, 077, 079, 084

Error Message

Description

INTERNAL ERROR

The thermostat has an internal fault. This error cannot be field repaired. 
Contact your wholesaler or tekmar sales representative for details 
on repair procedures.

POWER

The thermostat power supply voltage on wiring terminals R and C is 
too low. The thermostat does not operate until the voltage is increased 
to 24 V (ac).

Summary of Contents for tekmarNet 532





















Reviews:

No comments

Brands by name

Popular brands

Load more brands