POWER PIPE™ SYSTEM
Power Pipe™ Stake
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
1. Make watertight connections from remote
magnetic transformer to fixture leads using
waterproof wire connectors. (By Others)
STAKE WITH “B” CAP:
2. Attach ground from branch circuit to screw in
transformer T-housing. Place transformer and
connectors into T-housing.
3. Attach C cap and transformer T-housing
to Power Pipe™ with (3) #8-32 round head
Phillips stainless steel screws at base of
housing to secure to Power Pipe™ with Phillips
screwdriver.
WIRING DIAGRAM
120V
12V
Lamp
COM
GROUND
Transformer
COM
GROUND IN T-HOUSING
WIRING DIAGRAM
Junction Box/Stake w Transformer and B Cap
120V
12V
Fixture
COM
GROUND
Transformer
COM
GROUND IN T-HOUSING
WIRING DIAGRAM
Junction Box/Stake w Transformer and C Cap
1. Make watertight connections from primary
branch circuit to primary side of transformer
using waterproof wire connectors. (By Others).
Attach secondary leads from transformer to
fixture leads using waterproof wire connectors.
(By Others).
See wiring diagram.
STAKE WITH INTEGRAL TRANSFORMER T-HOUSING WITH “C” CAP:
RELEASE DATE
9-12-17
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF TEKA ILLUMINATION AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING
IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF TEKA ILLUMINATION IS STRICTLY FORBIDDEN.
DRAWING
NUMBER
INS-001082
2. Route the necessary UL approved under
ground branch circuit or low voltage wiring
to Power Pipe™ necessary for appropriate
installation. Leave enough length to make
connections to lamp leads.
3. Back fill hole with soil and/or prep for
concrete.
4. Pull branch circuit or low voltage wiring
necessary for appropiate installation (By
Others).
1. Excavate trench according to designed lighting
plan. Dig hole a minimum of 24” deep and 10” wide
to accommodate Power Pipe™ at desired fixture
locations.
INSTALLATION OF POWER PIPE™ STAKE
Finished grade
Pea gravel or sand
Finished grade
Finished grade
Stability Flange
Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
Finished grade
Pea gravel or sand
Finished grade
Finished grade
Stability Flange
Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
Finished grade
Pea gravel or sand
Finished grade
Finished grade
Stability Flange
Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
2. Attach B cap to Power Pipe™ with (3) #8-32
round head Phillips stainless steel screws at
base to secure to Power Pipe™ with Phillips
screwdriver.
120V
12V
Fixture
COM
Remote
Transformer
COM
120V
12V
Fixture
COM
GROUND
WIRING DIAGRAM
Integral
Transformer
COM
GROUND IN HOUSING
WIRING DIAGRAM
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.tekaillumination.com • [email protected]
