Teguar TMT-4391-08 Series Startup Manual Download Page 10

Declaration of Conformity 

CE Conformity Statement 
 

Radio products with the CE alert marking comply with the 
R&TTE Directive (1999/5/EC) issued by the Commission 
of the European Community. Compliance with this 
directive implies conformity to the following European 
Norms (in brackets are the equivalent international 
standards). 
• EN 60950-1 (IEC60950-1) - Product Safety 
• EN 300 328 Technical requirement for radio equipment 
• ET S301 489 General EMC requirements for radio 
equipment 
Products that contain the radio transmitter are labeled 
with CE alert marking and may also carry the CE logo. 
 

FCC Compliance Statement 
 

This equipment generates,  uses and can radiate radio 
frequency energy and, if not installed and used in 
accordance with the instructions, may cause harmful 
interference to radio communications. However, there is 
no guarantee that interference will not occur in a 
particular installation. If this equipment does cause 
harmful interference to radio or television reception, 
which can be determined by turning the equipment off 
and on, the user is encouraged to try to correct the 
interference by one of the following measures: 
• Reorient or relocate the receiving antenna. 
• Increase the separation between the equipment and 
receiver. 
• Connect the equipment into an outlet on a circuit 
different from that to which the receiver is connected. 
• Consult the dealer or an experienced radio/TV 
technician for help. 
 
To assure continued compliance, any changes or 
modifications not expressly approved by the party 
responsible for compliance could void the user's 
authority to operate this equipment. (Example: use only 
shielded interface cables when connecting to computer 
or peripheral devices). 
 
This device complies with Part 15 of the FCC Rules. 
Operation is subject to the following two conditions: 
1) 

This device may not cause harmful interference, 
and 

2) 

This device must accept any interference received, 
including interference that may cause undesired 
operation. 

 

15.21

   

Any changes or modifications not expressly approved by 
the party responsible for compliance could void the 
authority to operate equipment.   
This device and its antenna must not be co-located or 
operating in conjunction with any other antenna or 
transmitter.   
End-users and installers must be provided with antenna 
installation instructions and transmitter operating 
conditions for satisfying RF exposure compliance.   
For product available in the USA/Canada market, only 
channel 1~11 can be operated. Selection of other 
channels is not possible. 
 
 
 
 

FCC Radiation Exposure Statement 
 

This equipment complies with FCC RF radiation 
exposure limits set forth for an uncontrolled environment 
for body-worn configuration in direct contact to the 
phantom.   
This device complies with FCC radiation exposure limits 
set forth for an uncontrolled environment. 
 
This equipment complies with FCC radiation exposure 
limits set forth for an uncontrolled environment. End user 
must follow the specific operating instructions for 
satisfying RF exposure compliance. This transmitter 
must not be co-located or operating in conjunction with 
any other antenna or transmitter. 
The portable device is designed to meet the 
requirements for 
exposure to radio waves established by the Federal 
Communications 
Commission (USA). These requirements set a SAR limit 
of 1.6 W/kg 
averaged over one gram of tissue. The highest SAR 
value reported under 
this standard during product certification for use when 
properly worn on the body 
 

IC warning statement 

 

This device complies with Industry Canada’s 
license-exempt RSSs. Operation is subject to the 
following two conditions:    (1) This device may not cause 
interference; and    (2) This device must accept any 
interference, including interference that may cause 
undesired operation of the device. 
 
Le présent appareil est conforme aux CNR d'Industrie 
Canada applicables aux appareils radio exempts de 
licence. L'exploitation est autorisée aux deux conditions 
suivantes : (1) l'appareil ne doit pas produire de 
brouillage, et (2) l'utilisateur de l'appareil doit accepter 
tout brouillage radioélectrique subi, même si le brouillage 
est susceptible d'en compromettre le fonctionnement. 
 
This radio transmitter has been approved by Industry 
Canada to operate with the 
antenna types listed below with the maximum 
permissible gain and required 
antenna impedance are strictly prohibited for use with 
this device. 
 
Le present emetteur radio a ete approuve par Industrie 
Canada pour fonctionner 
avec les types d'antenne enumeres ci-dessous et ayant 
un gain admissible maximal 
et l'impedance requise pour chaque type d'antenne. Les 
types d'antenne non inclus 
dans cette liste, ou dont le gain est superieur au gain 
maximal indique, sont 
strictement interdits pour l'exploitation de l'emetteur. 
 
(i)the device for operation in the band 5150–5250 MHz is 
only for indoor use to reduce the potential for harmful 
interference to co-channel mobile satellite systems; (For 
devices installed in vehicles point i. is not required.) 
 
Users should also be advised that high-power radars are 
allocated as primary users (i.e. priority users) of the 
bands 5250-5350 MHz and 5650-5850 MHz and that 
these radars could cause interference and/or damage to 

Summary of Contents for TMT-4391-08 Series













Reviews: