background image

• USING THE SELF-CLEANING FUNCTION :

In order to extend the life of your iron, use the Self-Cleaning function once per 
month.

- Unplug your iron and set the steam control on DRY      .

- Fill the water tank up to the limit (see recommendations for the types of water to use).

- Leave water tank filler cover open until the end of the operation.

- Place your iron on its heel and set the thermostat control on MAX.

- Plug in your iron and wait until the thermostat light goes out.

- Unplug the iron and hold it over a sink in the horizontal position.

- Place the steam control on MAX.

- Raise the anti-calc valve without removing it completely.

- Shake the iron gently, over the sink, until all of the water in the water tank (with the 

impurities) has flowed out via the sole plate.

- At the end of the operation, push the anti-calc valve back into position.

- Turn the iron back on for 2 minutes, setting it on its heel, to dry the sole plate.

- Unplug the iron, and when the soleplate is just warm, wipe it with a soft cloth.

• CLEANING THE SOLE PLATE:

- While the soleplate is still just warm, clean it by rubbing it with a moist, non-metallic pad.

Recommendation :

The self-cleaning function helps to delay the scaling of your iron.

3- MAINTAINING YOUR IRON  

(continued)

4- STORING YOUR IRON

- Unplug it and wait until the sole plate has cooled off.

- Empty the water tank and set the steam control to DRY.

- Store the iron on its heel.

GUARANTEE (U.K. ONLY)

Details of the guarantee are shown on the guarantee card enclosed with

the appliance.This guarantee does not affect your statutory rights.

Should service or further information be required please contact the Tefal

Customer Relations Department (see Helpline or enclosed Service

Information leaflet).

Do not attempt  to dismantle the appliance yourself – this will negate the

guarantee.

In line with a policy of continuous product improvement,Tefal reserves the

right to change product specifications without prior notice.

NOT 033101 GB-F-AR-FAR  11/03/04  10:07  Page 4

Summary of Contents for SUPERGLIDE

























Reviews: