Teeter NXT-S Assembly Instructions Manual Download Page 8

STEP 1

Assemble A-Frame Base & Support Handles

• On a level surface, position the A-Frame so that it is standing upright  
  and the Stability Feet are on the ground.

• Gently push down on the Spreader Arms to ensure they are fully open  
  and in the “locked” position (Figure 1).

• Look for temporary circular assembly assistance labels on the  
  A-Frame. 

RIGHT, LEFT, FRONT,

 and 

REAR

 indicate your position while 

  using the equipment, not facing it. These labels can be removed easily  
  upon completion of assembly.

Assemble Support Handles

• Locate the Handle Assembly Hardware Kit (HK1009)

• Insert the handles into the A-Frame (Figure 2), so that the long part  
  of the handles are parallel with the rear legs of the A-Frame. 

• Insert the Bolts from the inside through the Hinge Plates and   
  Handles. Hand tighten with the nuts on the outside of the A-Frame  
  (Figure 2a).

• Tighten with the wrenches provided.

Assemble Hinge Covers to Hinge Plates

• Locate the Hinge Cover Assembly Hardware Kit (HK1002).

• Select the corresponding Hinge Covers for the left and right sides of  
  the A-Frame by aligning each with the shape of the Hinge Plate  
  (Figure 3).

• Secure with (2) Allen Head Bolts for each side using the 5mm   
  Allen Wrench provided. Be careful not to overtighten.

6

REV.

DESCRIPTION

REV.DATE

APP.DATE

APPROVED

說明書-0513      2015/5/11

D

細部放大圖 D

比例 1 : 7

C

A

B

D

E

6

5

4

3

2

9

8

7

C

A

B

D

E

F

G

H

1

2

3

4

5

6

7

8

9

F

G

H

1

 - Spreader Arms 

2

 - Crossbar

LEFT

FIGURE 1

1

2

REAR

FRONT

FIGURE 3

FIGURE 1a

UNLOCKED

FIGURE 2

FIGURE 2a

RIGHT

Summary of Contents for NXT-S





















Reviews: