Tecumseh OV490EA Operator'S Manual Download Page 9

181-887-14

Four-Cycle Engine • Vertical Crankshaft • Air-Cooled

Page 7

II. Independent Speed and Choke Controls

1.

To avoid carbon monoxide poisoning, make sure 
engine is outdoors in a well-ventilated area.

2.

Move engine speed control to “FAST” position and set 
choke control to “FULL” position (see equipment manu-
facturer’s instructions). See Figures 9, 10, 11 and 12.

 NOTES

Generator and Water Pump applications may have the 
choke lever mounted on the engine. See Figure 12. 

If restarting a warm engine after a short shutdown, move 
Speed Control to “FAST” position and move Choke Control 
to “NO CHOKE” position.

3.

Push starter button or turn ignition switch key (see 
equipment manufacturer’s instructions) to start engine.

 NOTES

DO NOT operate an electric starter for more than 5 seconds 
each attempt.

If engine fails to start after 3 attempts repeat steps 2 thru 3.

4.

When engine starts:

a. Release starter button or ignition switch key.

b. Next, move choke control to “1/2 CHOKE” position 

until engine runs smoothly.

c. Next, move choke control to “NO CHOKE” position.

5.

Finally, move engine speed control to desired speed in 
“RUN” range.

 NOTES

If engine starts, but falters when choke is moved to “NO 
CHOKE” position:

a. Momentarily move choke control back to “FULL 

CHOKE” position.

b. Next, move choke control to “1/2 CHOKE” position 

until engine runs smoothly.

c. Finally, move choke control to “NO CHOKE” 

position.

If engine dies after control is moved to “NO CHOKE” 
position, repeat steps 2 thru 5 to restart engine.

6.

If engine fires but does not continue to run, move 
choke control lever to “NO CHOKE” position and start 
engine.

7.

If engine fails to start after 3 attempts in the “NO 
CHOKE” position, move choke control to “FULL 
CHOKE” position and start engine.

8.

If engine does not start after following steps 1 thru 7, 
contact your Authorized Tecumseh Servicing Dealer. 
DO NOT attempt to start or troubleshoot this engine in 
any other way

.

Figure 10. Independent Speed and Choke Controls

Figure 11. Choke Control Positions

Figure 12. Engine Mounted Choke Lever

Choke 
Control

Speed 
Control

1. No Choke

2. 1/2 Choke

3. Full Choke

1

2

3

1. No Choke

2. 1/2 Choke

3. Full Choke

1

2

3

Summary of Contents for OV490EA

























Reviews: