background image

RESPIRATOR SPECIFICATIONS

The power must be turned off when replacing the filters. Install the spark screen, pre-filter, 

and particulate filter (gas filter if any) in filter cover.

Before installed, always make sure filter material is intact and dry with no tears or other 

damages. Install the filter cover assembly to the blower unit by engaging tabs on filter 

cover into bracket on blower unit and rotate assembly to close. Push filter cover assembly 

down until latch clicks into position securing filter cover assembly. Inspect both sides of 

cover  to  see  that  the  filter  cover  is  properly  installed.  To  replace  filter,  push  latch  into 

release filter cover and replace filter as fig.1 shown.

When  to  replace  the  filter:

  If  the  filter  gets 

blocked by contaminants, all the three points 

of warning lights will flash, accompanied 

with vibrate and bleeping sound. Please 

immediately exit contaminated environment 

and check the status.

ASSEMBLING & SPARE PARTS

fig.1

3

Manufacturer’s minimum design flow rate: 165+lpm (5.8+cfm) 
Low speed: 170+lpm (6+cfm) 
High speed: 210+lpm (7.4+cfm)
Battery type: rechargeable Li-ion battery
Battery duration: 9 h - low speed (170+lpm); 5-6 h - high speed (210+lpm)
Battery charge time: 1 hour

Battery life: ≥ 500 charges
Filter efficiency: 99.97%

Alarms: Visible, audible and vibrate

Operating temperature: -4°F to 140°F (-20°C to 60°C)

Storage temperature: -4°F to 113°F (-20°C to 45°C)

Operating R.H.: < 90%

Storage R.H.: < 85%

1020g (Blower unit + fast-charging standard battery)

EN12941 (Classifications please refer to the label on headtop)

AS/NZS1716: 2012 - Freflow V1, Particle filter with class P3 inside

Airflow Rate

Fast-charging

Standard Battery

Filter

Temperature

Relative Humidity 

(R.H.)

Weight
Respirator Approval

Limited 

storage 

life

Unopened filter: 5 years after production, details pls refer 

to the 'Do not use after ***' on the label of filter.
Installed  filter:  should  be  well-kept  under  instruction 

given condition.

For an installed filter which not use yet, it’s suggest to 

store no more than one year.

Summary of Contents for Freflow V1

















Reviews: