Techpro IPOB-EL3IRE User Manual Download Page 4

iii 

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens 

surface. 

Always use the dry soft cloth to clean the device.  If there is too much dust, please use the water to 

dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the 

device. 

Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera. 

Dome enclosure is the optical component, do not touch the enclosure when you are installing the 

device or clean the enclosure when you are doing maintenance work. Please use professional optical 

clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result 

in poor IR effect of camera with IR function. 

  

7. Accessories

Be sure to use all the accessories recommended by manufacturer. 

Before installation, please open the package and check all the components are included. 

Contact your local retailer ASAP if something is broken in your package. 

Accessory Name

 

Amount

 

Network Camera Unit 

Quick Start Guide 

Installation Accessories Bag 

CD 

Warranty Card and Certificate 

Summary of Contents for IPOB-EL3IRE





















Reviews: