background image

INSTALLATION

Important Precautions and  
Recommendations

After having unpacked the Technotape 3D oven, check to ensure 
that it is not damaged. In case of doubt, do not use it and 
consult your supplier or a professionally qualified technician. 
Packing elements (i.e. plastic bags, polystyrene foam, packing 
straps, etc.) should not be left around.

• Do not attempt to modify the technical characteristics of the 

appliance as this may become dangerous to use.

• Do not carry out cleaning or maintenance operations on the 

appliance without having previously disconnected it from the 
electric power supply.

• After use, ensure that the power switch is in the off position.
• During and after use of the appliance, certain parts will beco-

me very hot. Do not touch hot parts. Care should be taken to 
avoid touching heating elements inside the oven. 

Caution

 

• This oven must be installed in accordance with these installa-
tion instructions.
• This appliance is to be installed
only by an authorized person.
• This oven shall only be operated by trained personnel.
• Incorrect installation, for which the manufacturer accepts no 
responsibility, may cause personal injury of damage.
• Always disconnect the oven from the power supply before 
carrying out any maintenance operations or repairs.

2.1 First Time Use

2.2 Installation

Instructions

1. The oven must be connected to the power supply. Check that 

the voltage corresponds to the value given in the rating plate 
and that the electrical cable sections can withstand the load 
specified on the plate. The plug must be connected to an 
earthed socket in compliance with safety standards.

2. Switch the oven on with the main switch. No further assembly 

is required.

3. Please continue to chapter 3 ‘Working with the 3D Sublimati-

on Oven’. 

Warning

When correctly installed, your product meets all safety require-
ments laid down for this type of product category. 

Fire risk!

 Do not store flammable material in the oven. Always 

use oven gloves when removing products from the oven whilst 
hot. The manufacturer declines all liability for injury to persons 
or damage to property caused by incorrect or improper use of 
the appliance.

DO NOT

 lift the oven by the door handle.

9

Summary of Contents for 3DT.SUB.OVN.001



















Reviews: