Technogym Selection Adductor User Manual Download Page 12

Adductor

12

Routine maintenance

  WARNINGS

The safety of the equipment is assured only on the condition that it is carefully inspected every two weeks for any signs 
of damage and/or wear.
Replace defective and worn components immediately, or alternatively remove the equipment from service. 

The equipment should always be kept clean and free of dust, in compliance with good hygiene practice, especially if it is used in a 
gym or by more than one person.
Use a moist cloth or a sponge and mild soap to clean the padded parts. 
Wipe the outside of the equipment every week using a damp sponge.
Do not use chemicals or solvents.

  WARNING

Be careful not to rub too hard on the drawings and instructions shown on the labels.

To oil the weight stack guide rails:

-  remove the protective panel covering the weight stack, following the instructions found in the paragraph headed 

Removing the 

front weight stack panel

;

-  use a soft cloth to remove any dust and oil residues from the guide rails;
-  slightly moisten the cloth with the oil supplied in the optional Basic Box kit;
-  using this cloth, apply a very thin layer of lubricant over the guide rails, taking care not to apply too much;
-  refit the protective panel on the weight stack. 

Call in the Technogym Technical Support Service for instructions on any maintenance operations not described in this manual.

Summary of Contents for Selection Adductor






















Reviews: