Part III
Sequencer
60
QQTG0701
Se
qu
en
cer
10.
Play the keyboard.
• Recording begins.
• You can also press the
START/STOP
button to start the
rhythm and begin recording.
• If the metronome is on, when you press the
START/STOP
button, a two-measure count plays, after
which recording automatically begins. In this case, the
rhythm does not start. Recording does not start until the
two-measure count is completed.
• The recording status is continuously updated on the dis-
play:
MEASURE= indicates the current measure.
TIME SIG.= indicates the current time signature.
MEMORY= indicates the remaining memory (%) avail-
able for recording.
• If you wish to redo the recording, press the REC STOP
button and then record again. To change the sounds and
effects, etc. please set them again.
• If you make a mistake in recording, you can correct a
specific portion of your performance without having to
redo the whole part. (Refer to page 64.)
11.
When you have finished recording, press the
REC STOP button on the display, or turn off
the
PROGRAM MENUS
button.
• When the
PROGRAM MENUS
button is turned off, the
ending command (END) is recorded. Note that, as long
as the ending command is not recorded, blank recording
continues even if you stop playing.
• The
SEQUENCER PLAY
button turns on.
Multi-track recording
Use the following procedure to record one track
while listening to the track or tracks already
recorded.
1.
Follow the procedure to record the first track,
and press the REC STOP button at the end of
the recording.
• The indication for the track just recorded changes from
“REC” to “PLAY”.
2.
Turn on the “REC” indication for the track you
wish to record next, and select the sounds and
effects, etc.
3.
Press the
START/STOP
button and begin
recording.
• Tracks for which “PLAY” is shown are played back, and
you can record in time with this.
• If you turn on the “REC” for the CONTROL track and
begin recording, the rhythm start will not be recorded.
4.
Press the REC STOP button at the end of the
recording.
5.
Repeat steps 2 to 4 for other tracks, as
desired.
6.
When multi-track recording is finished, turn off
the
PROGRAM MENUS
button.
• If you wish to store part settings that you modified after
recording as beginning song data, press the MIXER but-
ton and follow the PANEL WRITE procedure. (Refer to
page 63.)
CYCLE RECORD
This mode allows you to have specified record-
ing measures continuously repeated. Thus you
can record measures by adding notes during any
cycle.
1.
On the REALTIME RECORD display, specify
“REC” for a track number you are going to
record, and “PLAY” for track numbers you
wish to have played back.
2.
Press the CYCLE: OFF button.
• The display looks similar to the following.
3.
Use the START MEASURE
∧
and
∨
buttons
to specify the beginning measure number.
4.
Use the END MEASURE
∧
and
∨
buttons to
specify the ending measure number.
• The measure in which the END command has been
stored can also be specified.
5.
Press the
START/STOP
button.
• If the metronome is on, cycle recording of the specified
measures begins after a two-measure count.
6.
Play the keyboard.
• The specified measures are repeated, during which time
you can record by adding notes little by little at the correct
timing (over-dubbing).
• If you wish to erase all the performance data from the
specified measures, press the CLEAR button.
• If the CYCLE: ON button is pressed, it changes to OFF.
This button does not function during recording.
• To return to the REALTIME RECORD display, press the
EXIT
button.
• Cycle record can also be started from the REALTIME
RECORD display whenever the CYCLE: ON indication is
shown.
7.
When you have finished recording, press the
REC STOP button on the display, or turn off
the
PROGRAM
MENUS
button.
START
CYCLE END MEASURE: 4
1
2
3
4
END
08_Part III.fm 60 ページ ２００３年５月１６日 金曜日 午後５時４１分
Summary of Contents for SX-PR54
Page 4: ...4 QQTG0701 ...
Page 5: ...5 QQTG0701 ...
