Technics SL-C700, Owner'S Manual

Page: 18 / 40

18
The sound is interrupted.
≥ Depending on your environment, the audio may be
interrupted during playback. Check the operating
instructions of the connected device and the connection to
the device.
Playback does not start.
≥
Depending on your environment or connected devices, it
may take some time.
The system control function is not working.
≥ Connect the system connection cable to the system
terminal [CONTROL2] of the SU-C700.
≥
Connect the coaxial digital cable to the digital audio input
terminal [COAX2 IN] of the SU-C700.
The unit enters standby mode automatically.
≥ Is the auto off function turned on? ( > 14)
≥ If the SU-C700 is connected to this unit via the system
control function, this unit may automatically enter standby
mode when the SU-C700 enters standby mode. (
> 9, 16)
Incorrect display or play does not start.
≥ Make sure that the disc is compatible with this unit. (
>
17)
≥ There is moisture on the lens. Wait for about an hour and
then try again.
≥
Unfinalised CD-R and CD-RW cannot be played back.
Playback takes time to start .
≥
It may take some time for the disc to load if there are a lot
of tracks or folders on it.
The remote control does not work properly.
≥
To avoid interference, please do not put any objects in front
of signal sensor. (
> 7)
≥
Change the remote control code if other products react to
this remote control. (
> 16)
≥ If the SU-C700/ST-C700 is selected for the device to be
operated, press [CD] and retry the operation. (
> 8)
≥
When this unit and the SU-C700 are connected with an
audio cable, switch the input of the SU-C700 to “LINE”.
Pressing [DIMMER] changes the display, the light
and the indicator brightness
of the SU-C700/ST-
C700.
≥ [DIMMER] works for the SU-C700/ST-C700 as well as this
unit. Turn off the device that you want to maintain the
brightness level of, and press [DIMMER].
The following messages or service numbers may appear
on the unit’s display.
“Full”
≥
The number of programmed tracks is more than 25.
“Not Conditional”
≥
The function you have tried to use is not available with the
current settings. Check the steps and settings.
“No Disc”
≥ Insert the disc to be played (
>
11).
“No File”
≥
Insert the disc to be played ( > 11).
≥
Insert a disc that has MP3/WMA files on it ( > 17).
“No Play”
≥ A CD that is not in CD-DA , MP3 or WMA format is
inserted. It cannot be played.
≥
Examine the content. You can only play supported format.
(
> 17)
“Reading”
≥
The unit is checking the CD information. After this display
has disappeared, start operating.
“Remote  ” (“  ” stands for a number.)
≥
The remote control and this unit are using different codes.
Change the code on the remote control.
– When “Remote 1” is displayed, press and hold [OK] and [1] for
at least 4 seconds.
– When “Remote 2” is displayed, press and hold [OK] and [2] for
at least 4 seconds.
-- --
:
-- --
≥
The display time is over 99 minutes and 59 seconds.
Disc
Remote control
（ Supplied with the SU-C700/ST-C700 ）
Messages
(18)
SL-C700-SQT0934.book 18 ページ ２０１５年３月２４日 火曜日 午後５時３３分