manualshive.com logo in svg

Technicolor TG672, Setup And User Manual

Share
Download
Technicolor TG672 Setup And User Manual Download Page 147

139

12 SUPPORT

E-DOC-CTC-20100728-0008 v2.0

12.6 Reset to Factory Defaults

Resetting your Technicolor Gateway

If at some point you can no longer connect to the Technicolor Gateway or you want to make a fresh install, it may be useful 
to perform a reset to factory defaults.

Warning

A reset to factory default settings deletes all configuration changes you made. Therefore, after the reset a reconfiguration of 
your Technicolor Gateway will be needed.

Also your wireless clients will have to be re-associated, as described in 

“5 The Technicolor Gateway Wireless Access Point” on 

page 59

.

Methods

You can choose between:

Resetting the Technicolor Gateway via the Technicolor Gateway GUI

Reset the Technicolor Gateway via the Reset button

Resetting the Technicolor Gateway via the Technicolor Gateway GUI

Proceed as follows:

1

Browse to the 

Technicolor Gateway GUI

.

2

On the 

Technicolor Gateway

 menu, click 

Configuration

.

3

In the 

Pick a task

 list, click 

Reset my 

Technicolor Gateway.

4

The Technicolor Gateway restores the initial configuration and restarts.

5

The Technicolor Gateway returns to the Technicolor Gateway home page (unless the IP address of your computer is not 
in the same subnet as the default IP address of the Technicolor Gateway, being 192.168.1.254).

Reset the Technicolor Gateway via the Reset button

Proceed as follows:

1

Make sure the Technicolor Gateway is turned on.

2

Push the 

Reset

 button for 7 seconds and the release it.

Summary of Contents for TG672

























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands