Techni Sport TS83 Assembly Instructions Manual Download Page 6

Chairs’ height: Pull UP the lever under the seat. The chair goes down while sitting on it, or up if

you lift your body.

Seat tilting: Pull the same lever OUT horizontally to unlock this function, and IN to  lock again.

NOTE: Unlike regular office chairs, these racing/gaming chairs have their base components

off-center, and the tilting won’t be much and might actually feel hard to tilt.

Tilt tension: Turn the mechanism’s knob in either direction to apply more or less tension. With

less tension, the tilting will feel easier. Please read the above note about the tilting.

Backrest reclining: 

pull UP the lever located on the rear right side of the seat and release it 

when the desired position is reached.

WARNING

: For your safety, the seat’s tilt function 

should be in the 

LOCKED

(IN) position

prior to use the backrest reclining function. 

Armrest height: Pull UP the button that is under the armrest. Some models have additional 

functions like forward/back, in-out and pivot. 

CHAIR’S FUNCTIONS

P.5

Models: TS83, TS84, TS90, TS92, TSF44, TSXXL2

P.5

2

1

CHAIR’S FUNCTIONS

WARNINGS

• Do not exceed the indicated weight limit.

• Do not stand up on the chair or use it as ladder.

• Use the chair to seat only one person at a time.

• Do not use the chair if parts are damaged or if screws are loose or missing.

• Do not sit near the edge of the seat and always sit properly on the chair to avoid going 

beyond your balance point and fall off the chair.

• The chair is intended for teenagers and adults. If small children are using the chair, 

please keep close observation on them.

• Do not allow small children to play with the chair.

• Not paying attention to these warnings could result in severe injuries.

• To clean the chair it is recommended to use a soft cloth lightly damped in a solution of 

smooth soap and water, then dry with a clean towel.

• Do not use solvents or abrasive materials to clean any part of the chair.

• Before applying a cleaning agent, test on a small hidden area of the chair, like 

underneath the seat.

• Do not expose the product to direct sunlight or to extreme environmental conditions.

• Every 4 months, inspect the chair completely and make sure that all screws are 

tighten.

CARE AND MAINTENANCE

3

Weight 

Limit

Model

250 Lbs

TS90
TS92

TSF44

300 Lbs

TS83
TS84

400 Lbs

TSXXL2

Summary of Contents for TS83









Reviews: