Techni Sport Echo TSF44 Assembly Instructions Manual Download Page 6

P.5

TS43, TS51, TS52, TS83, TS84, TS85, TS90, TS92, TSF44, TSXXL2

P.5

CHAIR’S FUNCTIONS

WARNINGS

CARE AND MAINTENANCE

• Chairs’ height: Pull UP the lever under the seat. The chair goes down while sitting on it, or up if

you lift your body.

• Seat tilting: Pull the same lever OUT horizontally to unlock this function, and IN to  lock again.

NOTE: Unlike regular office chairs, the racing/gaming chairs have their base components off-

center, and the tilting won’t be much and might actually feel hard to tilt.

• Tilt tension: Turn the mechanism’s knob in either direction to apply more or less tension. With

less tension, the tilting will feel easier. Please read the above note about the tilting.

• Backrest reclining: pull UP the lever located on the rear right side of the seat and release it

when the desired position is reached. 

WARNING

: For your safety, the seat’s tilt function 

should be in the LOCKED (IN) position prior to use the backrest reclining function.

• Armrest height: Pull UP the button that is under the armrest. Some models have additional

functions like forward/back, in-out, and pivot.

• Do not exceed the indicated weight limit.

• Do not stand up on the chair or use it as ladder.

• Only one person at a time can sit on the chair.

• Do not use the chair if parts are damaged or if screws are loose or missing.

• This chair has the base components off-center than regular chairs. Do not sit near the edge of the

seat to avoid going beyond your balance point and falling off the chair, and always sit properly.

• If small children are sitting on the chair, please keep close observation on them.

• Do not allow small children to play with the chair.

• Not paying attention to these warnings could result in injuries.

• To clean the chair it is recommended to use a soft cloth lightly damped in a solution of smooth

soap and water, then dry with a clean towel.

• Do not use solvents or abrasive materials to clean any part of the chair.

• Before applying a cleaning agent, test on a small hidden area of the chair, like underneath the

seat.

• Do not expose the product to direct sunlight or to extreme environmental conditions.

• Every 4 months, inspect the chair completely and make sure that all screws are tighten.

4

3

2

1

5

2

3

2

1

4

5

Weight 

Limit

Models

250 

Lbs

TS43

TS85

TS90

TS92

TSF44

300 

Lbs

TS51

TS52

TS83

TS84

400 

Lbs

TSXXL2

Summary of Contents for Echo TSF44









Reviews: