background image

TEP-0700-IMX7 HARDWARE MANUAL 

– VER 1.00 – MAR 11 2019 

Page 

4

 of 

26

 

1. Introduction 

1.1. General Care and Maintenance 

 
Your device is a product of superior design and craftsmanship and should be treated with care.  
 
The following suggestions will help you. 

 

Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain 
minerals that will corrode electronic circuits. If your device does get wet, allow it to dry completely. 

 

Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be 
damaged. 

 

Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, 
damage batteries, and warp or melt certain plastics. 

 

Do not store the device in cold areas. When the device returns to its normal temperature, 
moisture can form inside the device and damage electronic circuit boards. 

 

Do not open the device while power is on. 

 

Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and 
fine mechanics. 

 

Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device. 

 

Do not paint the device. Paint can clog the parts and prevent proper operation. 

 

Unauthorized modifications or attachments could damage the device and may violate regulations 
governing radio devices. 

 
These suggestions apply equally to your device, battery, charger, or any enhancement. If any device is 
not working properly, take it to the nearest authorized service facility for service. 
Regulatory information 

Disposal of Waste Equipment by Users in Private Household in the European Union 
This symbol on the product or on its packaging indicates that this product must not be 
disposed of with your other household waste. Instead, it is your responsibility to dispose 
of your waste equipment by handing it over to a designated collection point for the 
recycling of waste electrical and electronic equipment. The separate collection and 
recycling of your waste equipment at the time of disposal will help to conserve natural 
resources and ensure that it is recycled in a manner that protects human health and the 
environment. For more information about where you can drop off your waste equipment 

for recycling, please contact your local city office, your household waste disposal service or the shop 
where you purchased the product. 
 

We hereby declare that the product is in compliance with the essential requirements and 
other relevant provisions of European Directive 2014/53/EU (Directive on the 
harmonisation of the laws of the Member States relating to the making available on the 
market of radio equipment and repealing Directive 1999/5/EC). 

 

 

Summary of Contents for TEP-0700-IMX7



























Reviews: