manualshive.com logo in svg

TechNexion TEP-0500-IMX7, Product Manual

Share
Download
TechNexion TEP-0500-IMX7 Product Manual Download Page 21

TEP-0500-IMX7 HARDWARE MANUAL 

– VER 1.00 – AUG 03 2018 

Page 

21

 of 

27

 

5. Mounting 

 
This section describes the mounting procedures for TEP-0500-IMX7. The material in area of the mounting 
must provide sufficient strength for safe mounting of this device.  

5.1. VESA Mounting 

 
The TEP-0500-IMX7 is compatible with the VESA MIS-C Standard 35*75mm hole pattern. There are 4 
VESA MIS-C (M4) mounting holes on the rear side of the device. M4 screw holes are a depth of 4mm. 
 
  
                                                                                                                                          
                                                                                                                                          
                                                                                                                                          

                                                                

1

                                        

2                    

                                                                                                                                          
                                                                                                                                          
                                                                                                                                          

                                                                

3

                                        

4

  

                   

                                                                                                                                          
                                                                                                                                          
                                                                                                                                           

                                                                                                  

                                                                                                                                            

 

 

Summary of Contents for TEP-0500-IMX7




























Reviews:

No comments

Brands by name

Popular brands

Load more brands