3.3
Rear Mounting and Mounting Clips Installation (TEP-0500-IMX6UL only)
3.4
Surface Mounting Installation
4
External Connectors
There are 8 mounting holes (M4) on the rear side of the device required for surface mounting. M4 screws with at
least 5mm head-to-tip length are required to secure this device.
There are 5 mounting clips required for rear mounting.
• All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval system, or transmitted, in any
form or by any means whether, electronic, mechanical, or otherwise without the prior written permission of TechNexion Ltd.
• No warranty of accuracy is given concerning the contents of the information contained in this publication. To the extent permitted
by law no liability (including liability to any person by reason of negligence) will be accepted by TechNexion Ltd., its subsidiaries or
employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
• TechNexion Ltd. reserves the right to change details in this publication without notice. Please download the most updated version
at: https://www.technexion.com/support/download-center/
TEP-0500-IMX6UL
TEP-0700-IMX6UL
TEP-0500-IMX6UL
TEP-0700-IMX6UL
TEP-0500-IMX6UL
1
2
3
4
5
6
7
8
9
10
11
12 13
14
15
16
1
2
3
4
5
6
7
8
9
10
11
12 13
14
15
16
Description
No.
No.
Description
1
RS-XXX1 (Serial Port) connector
2
RS-XXX2 (Serial Port) connector
3
CAN Bus connector
4
GPIO1 connector
5
GPIO2 connector
6
GPIO3 connector
7
MicroSD cardslot
8
USB OTG (Type-C) connector
9
LED Light indicator
10
S1 Boot Select button
11
Reset button
12
USB Host connector
13
LAN2 RJ45 connector
14
LAN1 RJ45 and PoE (optional)
15
16
Power Input connector
Grounding screw
Phone: +886-2-82273585
Web: www.technexion.com
16F-5, No. 736, Zhongzheng Road,
ZhongHe District, 23511, New Taipei City, Taiwan
© 2001-2018 TechNexion Ltd.
2018-10-31
5.1
Serial Port Connector (RS-XXX1/RS-XXX2)
5
Pin Definition
Header: Molex 43045-1012 (10-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-1000 (10-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
Port
Pin #
RS-XXX1 Signal Device
Device
RS-XXX2 Signal
1
GND
GND
2
SERIAL1A_TXD
ttymxc0
ttymxc2
ttymxc2
ttymxc3
ttymxc3
3
SERIAL1A_RXD
ttymxc0
4
NC
5
NC
6
GND
ttymxc1
7
SERIAL1B_TXD
ttymxc1
8
SERIAL1B_RXD
9
NC
10
NC
SERIAL2A_TXD
SERIAL2A_RXD
NC
NC
GND
SERIAL2B_TXD
SERIAL2B_RXD
NC
NC
1
2
3
4
5
6
7
8
9
10
5.2
CAN Bus Connector (CANBus)
Header: Molex 43045-1212 (12-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-1200 (12-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
GND_CAN
CAN1A_TERM_P
can1
CAN1A_P
can1
CAN1A_N
can1
CAN1A_TERM_N
can1
NC
GND_CAN
CAN1B_TERM_P
can2
CAN1B_P
can2
CAN1B_N
can2
CAN1B_TERM_N
can2
NC
Port
Pin #
Signal
Interface
1
2
3
4
5
7
6
8
9
10
11
12
1
2
3
4
5
6
7
8
9
10
11
12
5.3
Digital I/O Connectors (GPIO1/GPIO2/GPIO3)
Header: Molex 43045-0812 (8-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-0800 (8-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
Port
Pin # GPIO1/2 Signal GPIO1/2 Description GPIO3 Signal GPIO3 Description
Voltage
1
GPIO1A/2A DIG_IN1/OUT1
GPIO2A
3.3V
3.3V
3.3V
3.3V
3.3V
ADCI_INO
2
GPIO1B/2B DIG_IN2/OUT2
GPIO3B
PWM_OUT or DIG_IN2/OUT2
3
GND_DIO
Ground for digital I/O GND_DIO
Ground for digital I/O
4
NC
NC
5
GPIO1C/2C DIG_IN5/OUT5
GPIO3C
PWM_OUT or DIG_IN5/OUT5
6
GPIO1D/2D DIG_IN5/OUT6
GPIO3D
PWM_OUT or DIG_IN6/OUT6
7
VCC_DIO
Supply output
VCC_DIO
Supply output
8
NC
NC
1
2
3
4
5
6
7
8
2
1
4
3
The unit is preloaded with software that can download and install a selection of OS images over hardwired
network. Simply connect a network to the unit through the Ethernet LAN RJ45 connector and power it up, then
follow the steps on the screen to load the software. Local proxies will interfere with this process. For more
information, go to our Knowledge Base at: https://www.technexion.com/support/knowledge-base/
6
Software Installation
3
4
