• If you buy your evaluation kit with 8” or 10.1” panel, please refer to the separate 8” / 10.1” panel installation guide included with the panel for more details.
After you finish the panel installation, return to this guide.
!
3.4
Display (optional)
3.5
Final steps
4.1
Power Connector (DCIN1 +12v)
4.2
SWITCH1-8 Default Boot Mode Switches
4
Pin Definition
5
External Connectors
Please follow the steps below to properly install the 5” display.
Step 1: Prepare evaluation board, MIPI expander board and screws.
Step 2: Locate the MIPI expander board and align the 70-pin connectors, gently press the connector on the back of the expander board onto the connector on the
evaluation board until you hear a click sound.
Step 3: Use three screws to secure the MIPI expander board to the development board.
Step 4: Locate the MIPI Display connectors on the expander board. Swivel the black retaining clips upward.
Step 5: Insert end of the TOUCH and MIPI Display FPC cables into the connectors on the board. The silver pins on the FPC cable should be facing down. Then swivel
the retaining clips back down to hold the FPC cables in place.
Step 6: Remove the protective transparent film from the display.
This product features one 2-pin Micro-Fit 3.0 power connector: DCIN1 +12v.
The AXON-WIZARD-IMX8M-MINI features internal Default Boot Mode setting.
Now your kit is almost assembled.
Step 1: Connect the RTC backup battery.
Step 2: Attach the extender cable to the Wi-Fi antenna.
Step 3: Connect the 2-pin Micro-Fit 3.0 cable to power up the evaluation kit.
• All Rights Reserved. No part of this document may be photocopied, reproduced, stored in a retrieval system, or transmitted, in any form or by any means whether, electronic, mechanical, or otherwise
without the prior written permission of TechNexion Ltd.
• No warranty of accuracy is given concerning the contents of the information contained in this publication. To the extent permitted by law no liability (including liability to any person by reason of
negligence) will be accepted by TechNexion Ltd., its subsidiaries or employees for any direct or indirect loss or damage caused by omissions from or inaccuracies in this document.
• TechNexion Ltd. reserves the right to change details in this publication without notice. Please download the most updated version at: https://www.technexion.com/support/download-center/
Phone: +886-2-82273585 Web: www.technexion.com
16F-5, No. 736, Zhongzheng Road, ZhongHe District, 23511, New Taipei City, Taiwan
© 2001-2020 TechNexion Ltd.
2020-09-07
6
Software Installation
The unit is preloaded with software that can download and install a selection of OS images over hardwired network. Simply connect a network to the unit through the LAN RJ45
connector and power it up, then follow the steps on the screen to load the software. Local proxies will interfere with this process. For more information, go to our Knowledge Base
at: https://www.technexion.com/support/knowledge-base/
Header on AXON-WIZARD-IMX8M-MINI: Molex 43045-0212 (2-pin Micro-Fit 3.0).
Cable receptacle: Molex 43025-0200 (2-pin Micro-Fit 3.0) plug with crimp contact Molex 43030-0007.
NOTE: *SW1 is OFF by default.In order to boot from eMMC.
*BOOTCTRL0 ,1 should be high by default.
Description
No.
No.
Description
1
2
3
4
5
6
16
15
17
18
19
20
21
22
23
24
25
26
27
7
8
9
10
11
12
13
14
Power Input connector
LAN2 RJ45 connector
LAN1 RJ45 connector
HDMI connector
CONSOLE connector
USB OTG (Type-C) connector
Micro-SD1 card slot
USB Host connectors (2x)
Audio Jack
CLIX connector
MIPI Camera 1 connector
MIPI Camera 2 connector
Touch connector
R-Speaker connector
L-Speaker connector
LVDS connector
RTC Battery connector
MIPI Display connector
Audio channel selection
SATA_PWR_1 connector
SATA1 connector
40-pin expansion header
12-pin expansion header
Micro-SIM1 card slot
Micro-SIM2 card slot
mini-PCIe1 connector
mini-PCIe2 connector
3
4
1
2
3
1
2
4
5 6 7
8
9
10
11
12
13
14
15
24
26 27
4
5
6
Front view:
16
17
18
19
20
21
22
23
Rear view:
25
3
1
2
3
DCIN1 +12v:
Header
Pin # Signal
1
2
GND
VCC
Description
Ground
DC Voltage input (12V DC)
1
2
SW:
Device
SW1-1
SW1-2
OFF
ON
OFF
OFF
OFF
ON
eMMC
SDIO
USB_A_OTG