manualshive.com logo in svg

Techne IFB-51, Instruction Manual

Share
Download
Techne IFB-51 Instruction Manual Download Page 5

BEFORE USE

Thank you for purchasing this Techne product. To get the best performance from the equipment, and for 
your own safety, please read these instructions carefully before use. If there is any doubt relating to the
proper use of this equipment, the staff at Cole-Parmer Ltd. or your supplier will be happy to assist you.

UNPACKING

When unpacking the unit please ensure that the following have been removed from the packaging:

Part code 

FIFB51D or FIFB52D 
7002661 

Item description

IFB Industrial 

f

luidised 

b

ath

 

Instruction 

m

anual

Eurotherm 

c

ontroller 

i

nstructions

 

Warranty 

c

ard

Please note that the aluminium oxide fluidising medium must be ordered separately:

Part code 

Item description

Brown/A

L

O Alundum - brown aluminium oxide, 25kg.

The IFB-51 requires 40kg of aluminium oxide and the IFB-52, 73kg of aluminium oxide.

The user is advised to keep the original packaging in case the instrument ever needs to be returned for

 

service or repair. Cole-Parmer Ltd. accepts no responsibility for damage incurred unless the unit is correctly

 

packed and transported in its original packaging.

If the equipment is not used in the manner described in this manual and with accessories other than those 
recommended by the manufacturer, the protection provided may be impaired.

5

Summary of Contents for IFB-51

































Reviews:

No comments

Brands by name

Popular brands

Load more brands