Technalogix TAV-500 Manual Download

Page: 48 / 57

Technalogix Ltd

VIII-8

POWER -

Tactile

button to turn carriers on and off. To turn off, must be depressed for

at least 2 seconds. Tied internally through DB9 connectors to all other
POWER buttons.

NAVIGATE -

Tactile button to refresh screen after two minute screen saver times out. All
monitoring and protection continues during screen saver.

SELECT-

Tactile button to refresh screen after two minute screen saver times out. All
monitoring and protection continues during screen saver.

RESET -

Tactile button to reset microcontroller in control board. Also clears existing
faults. Individual control board with reset comes back on with soft start feature.

RF IN –

RF input from modulator or processor. BNC connector, 50 ohm.

RF OUT –

500-watt RF output. Connects to RF IN on filter enclosure. N connector, 50
ohm.

DC IN –

DC input from power supply enclosure. Polarized to avoid improper hook up.

REMOTE PORT -

pin 1: ground to reset microcontroller, float otherwise

pin 2: ground for 2 seconds to toggle carrier on/off, float otherwise

pin 3: common ground

pin 4: DC power supply sample (28Vdc nominal)

Summary of Contents for TAV-500


























































Search results

Summary of Contents for TAV-500

Reviews:

Related manuals for TAV-500

Brands by name

Popular brands

Technalogix TAV-500, Manual

Search results

Summary of Contents for TAV-500

Reviews:

Related manuals for TAV-500

Brands by name

Popular brands