background image

Detail Information of Display

Display

Contents

Display

Contents

Represents machine is in clean state .

At this time only beaters in the cylinder are 

stirring , pour water can clean the machine.

Represents machine is in stand by mode .

At this time long press SET can set parameter 

or others

Represents back temperature.

There will be alarm when it lower than -25 C 

but will not impactcapability of machine .

Represents the times of put out ice cream .

It scores 1 time when handle jack-up and touch 

the micros witch . There's a " ticktack " when 

micro switch is touched

Upper temperature represents hopper temperature.

Represents it lacks raw material in the hopper

The number represents the time left to start 

freezing again after stops.

During this period can be manually opened after 

the cooling or charge will automatically start after 

the cooling

At normal freezing state , it represents shape rate 

of material in freezing cylinder , when it reaches 

to 99% , the material are all ready and machine 

will stop automatically after working a while . At 

SET state , it represents the present shift of the 

machine

Represents it's in freezing state.

when it reaches to 99 % , the material are all 

ready and machine will stop automatically after 

working a while

Summary of Contents for TG300P


























Reviews: